Bedienungsanleitung Atmos A45SPT (Seite 52 von 72) (Englisch)

810414

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

www.atmos.cz

52-EN

Operation and Maintenance Manual - EN

f) S68 = 11… Reserve function for controlling boiler exhaust fan for DC40GSP and DC40SPT

boiler types when the function for automatic start after wood is burnt out is activated. This function

ensures that boiler exhaust fan is running only during wood burning after the wood is burnt out.

When the burner is run on pellets, the boiler exhaust fan remains switched off. This function is

used if you do not need or want to use the boiler exhaust fan while the burner is running. Special

adapter (jumper) and modules AD02 or AD03 (AD08) is not installed in DC40GSP and DC40SPT

boilers.

WARNING – this is not a standard settings for DC40GSP and DC40SPT boilers with the

function of automatic start (AUTOSTART – S34 = 1 or S34 = 2) after wood is burnt out

(standard setting is S14 = 13).

g) S68 = 12… Reserve function for direct control of pump in the boiler circuit from the burner

regulation (boiler terminal board). This function controls the pump in the boiler circuit without

using AD02 or AD03 modules. This is applicable only for boilers that do not allow heating with

wood (not even in emergency situations). E.g. D14P, P14, D21P, P21, D25P, P25, DxxPX, PXxx.

Pump output must be switched to reserve R5 on the boiler terminal board and the TK sensor must

be installed before this function can be activated. After activation, S37, S38, S39, S40 temperature

parameters must be checked and configured.

h) S68 = 13… Reserve function is the reverse output function for controlling the pump in

the boiler circuit from the burner regulation (output cable from boiler with a connector – white

inside) via AD02, AD03 or AD08 modules. This function controls the pump in the boiler circuit

using AD02, AD03 or AD08 modules ranged into a set with pump thermostat installed into the

boiler panel. After activation, S37, S38, S39, S40 temperature parameters must be checked and

configured.

i) S68 = 14… Reserve function for direct control of solar heating pump from the burner regulation

(boiler terminal board). This function control solar pump when automatic sensor switching function

is activated (S15 = 3), where the boiler is connected with accumulation tank equipped with solar

exchanger and collectors. The system requires TV, TK, TS and solar sensors to be connected to the

TSV solar panel. This function never uses AD02 or AD03 modules.

After activation, S26, S27, S28, S29, S30, S31, S32, S33 temperature parameters must be checked

and configured.

This function is specially designed for boilers: D14P, P14, D15P, P15, D20P, P20, D21P, P21,

D25P and P25

CAUTION - the direct controlling function of solar heating from pellet burner cannot

be used for DC40GSP and DC40SPT boilers and boilers with burner built into the upper

doors. This function also cannot be used when the pump is simultaneously controlled in the

boiler circuit from the burner regulation (TK sensor cannot be simultaneously in boiler and

accumulation tank)

(32)

TV,TK<

(33) TV,T-

SV>

(34) TV,TSV<

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A45SPT Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info