Bedienungsanleitung Atmos A85 (Seite 21 von 66) (Englisch)

810412

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

Operation and Maintenance Manual - EN

www.atmos.cz EN-21

15. Commissioning

CAUTION - The system may only be put in operation if the burner is connected to the

boiler, the boiler to a chimney with sufficient draught via a flue gas duct and in the fuel bin

there is a sufficient quantity of pellets of the corresponding quality. Pellets made of soft

wood without bark, i.e. white pellets with the diameter of 6 to 8 mm and length of 5

to 25 mm are considered as high-quality pellets. These pellets do not cake. Burning of

dark pellets or pellets with bark that contain visible dark dots produces cake that must

be removed from the burner mouth once a day. Otherwise the combustion chamber

and the feeding hose from the conveyor will get clogged.

For this reason the basic version of ATMOS burner A85 is equipped with pneumatic

cleaning which cleanses the burner’s combustion chamber after every burn out

or at regular intervals (factory setting is 4 hours – parameter S42, S43). Thanks to

pneumatic cleaning you can check or clean the burner’s combustion chamber only once

in a fortnight or a month.

INFO - The pellets have to be stored in dry and clean containers (areas). When filling

the fuel bin, the pellets must not be contaminated by foreign objects that could cause a

blockage of the conveyor or have an impact on the burning process.

Requirements for the external conveyor and pellet bin at the first start of the burner:

• The worm conveyor must be positioned in the bin in such a way to be able to easily pick up

pellets. In the case of a fuel bin whose pellet level will be higher than 2 metres a roof will have

to be installed over the conveyor to prevent blocking of the conveyor. Blocking of the conveyor is

caused by dust in the pellets in combination with high pressure caused by the height of the pellet

level. ATMOS 250, 500 and 1000 l pellet bins do not require the installation of the roof.

• The hose between the burner and conveyor must be tensioned, properly fixed and must have such

an inclination to enable trouble-free falling of pellets to the burner.

• The connector of the work conveyor must be plugged into the socket on the burner.

Procedure of drawing pellets to the conveyor

• Plug the connector of the external worm conveyor to a standard wall socket. As soon as the first

pellets get over the top point and start to fall to the burner via the elastic hose, plug the connector

of the external worm conveyor back into the socket on the burner.

Normal operation:

• On the control thermostat on the boiler panel set the required operation temperature of 80 - 90 °C

and turn on the switch of the burner located on the boiler panel and the main switch.

The STARTup mechanism consists of the following steps:

•

At the start the worm conveyor and the ignition spiral are started (the fan on the burner and the boiler

is stopped).

• The worm conveyor will run for the time set by parameter T1, necessary for the delivery of the

amount for pellets for optimum ignition. After the delivery of the ignition amount of fuel the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A85 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atmos A85

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info