Bedienungsanleitung Atmos A85 (Seite 38 von 66) (Englisch)

810412

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

www.atmos.cz

38-EN

Operation and Maintenance Manual - EN

If the function (parameter S34) is turned on in the boiler, the following practice is used for

boilers SP(X):

If the boiler is burning out but the wood container still contains enough wood, we may directly

switch the boiler switch from wood to pellets.

The pellet burner will perform a DIAGNOSTIC which will be used to ascertain the current status

of the boiler (temperature of exhausts, temperature of the boiler, temperature in the accumulation

tank)

If the conditions for immediate start of the burner are not met (see above), the burner will remain

on standby, where the flue exhaust fan will remain in operation (if set) so that the wood can

properly finish burning (S6 = 4). AUTOSTART will start flashing on the burner screen.

If the AUTOSTART sign flashes slowly, the conditions set by the function (S34 = 1 or S34 = 2)

are not met.

If the AUTOSTART sign flashes quickly, the previous conditions are met, but the conditions set

by function (S15 = 2) are not, which means that the temperature on the accumulation tank did not

drop below the value set by S16 or the regulation thermoregulator on the boiler is not activated, i.e.

the end switch is not pressed (a star is not displayed on the boiler screen near the thermoregulator

symbol)

If all the conditions are met, the burner will start automatically.

INFO - In case of an electric outage, the burner will perform a DIAGNOSTIC and, if all

conditions are met, will burn out and return to normal operation. Otherwise it will await the

fulfillment of previous conditions (drop of exhaust and water temperature).

If we want to use wood to heat up the boiler, it suffices to place the switch on the wood

position. However, it is better to first keep the switch on the „0“ position for 10 - 15 minutes

so that the burner can properly burn out. This is an ideal time to prepare the fuel for stoking.

WARNING - SP(X) boilers do not allow you to control the solar heating function directly

from the pellet burner. Additionally the TK and TSV sensors are used for measuring the

temperature of the boiler and exhausts during this function.

• Parameter S35 - characterizes the limit (max.) temperature of the boiler TK, during which the

burner will automatically start during the AUTOSTART function (S34 = 2)… (75 °C)

• Parameter S36 - characterizes the limit (max.) temperature of the exhausts TSV, during which the

burner will automatically start during the AUTOSTART function (S34 = 2)… (80 °C)

WARNING - after placing the exhaust sensor TSV on a side of the burner flue pipe, the

TSV temperature is not the exact temperature of the exhausts but the difference temperature

for the automatic start function. If we want to place the exhaust sensor directly on or into the

flue pipe to measure the exhaust temperature precisely, it is necessary to always use a sensor

with a higher heat resistance of up to 400 °C.

• Parameter S37 - characterizes the requires temperature of the boiler TK during which the pump in

the boiler circuit will be activated. This will only occur if the required temperature is reached and

the boiler is in OPERATION or burn-out mode (S14=13 with modules AD02 or AD03)… (75 °C)

It is also necessary to re-check or set parameters S38, S39, S40

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A85 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atmos A85

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info