Bedienungsanleitung ATTACK DPX Combi Pellet (Seite 54 von 100) (Englisch)

810510

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

After pressing the „S” by displayed „EFFECT ADJ.“ is in the left upper corner displayed „OUTPUT 1

(kW)“. In the left bottom corner will be „O:16“ (i.e. the actual value of the actuator output in kW).

To change the actuator output, press the „+“ button, until the required value is displayed in the

right bottom corner, i.g. „N:18“. If you press „S“ now, this new value (18 kW) will be saved for the

output level 1. After this, the output level 2 is displayed („OUTPUT 2“) and it can be set to the

required value. If it will not be changed, press „S“ to save the value indicated on display, i.g.

„N:22“, i.e. the output level 2 (OUTPUT 2) will be 22 kW.

If you wish to let the display without saving the changes, press „ESC“.

Setting of ignition:

Here you can adjust the ration of fuel for ignition in %; this value

was automatically calculated adequately to the weight given in

the Feeder setting – amount.

By pressing the „S“ button, the „Ignition amount 1“ is displayed in the left upper corner. Changes

are made in %, the starting amount was pre–set to 170 g. If you increase this amount to 110%,

the starting amount will be changed to 187 g.

If the first trial of the burner ignition fails, the Ignition amount 2 is activated, which is pre–set

from production to 45 % from 170 g, i.e. 76,5 g.

Setting of time of the test blow–through

Time of the test blow–through defines the time, within which will

be the boiler and the chimney ventilated before beginning the

combustion (10 – 100 seconds).

For boilers, at which there is tough to achieve their draught, it is recommended to increase the

time of test blow–through. From production it is set to 15 sec.

Setting of the transition period:

Here you can select the duration since the first recognizing of the

fire up to the feeding of full amounts of pellets, adjusted by the

actuator output.

There are two parameters of the transition phase: the first is 14 kW and the second is 30 kW. The

time set by the first parameter determines, how long it will take to achieve 14 kW, time of the

second parameter determines time to achieve 30 kW since the fire is recognized. The lower the

required output is, the shorter is the period necessary to achieve it.

Setting of the fuel supply during the transition phase:

Here you can set the fuel amounts that are feeded during the

transition phase, since the fire is recognized until the burner

achieves the output of 14 kW.

Set the required amount to be feeded into the burner after the fire recognition. The supplied

amount will be gradually increased with every ration during the stated period. From production

it is set to 15% from the full ration for 14 kW.

IGNITION SETTING

ENTER < > EXIT

TEST BLOWING

ENTER < > EXIT

TRANS. PHASE

ENTER < > EXIT

TRANS. FEED.

ENTER < > EXIT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK DPX Combi Pellet Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info