Bedienungsanleitung ATTACK DPX (Seite 15 von 92) (Englisch)

810499

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Turn the flue gas thermostat to „0 °C“. Put one layer of the medium thick wood logs (of approx.

50 mm length)through the upper door on a fire proof nozzle. Then, make the layer of thin wood

with the gap of 2 – 4 cm and lay splinters or wood wool and paper on it. Continue with 2 layers

of thin dry wood and complete it with the standard firewood. Turn the exhaust fan on and after

the wood is ignited, let the feeding door open for approximately 15 mm. Use the output

regulator to set the required water temperature (80 – 90 °C). When the fire is strong enough

(after approximately 10 minutes), close the feeding door. Set the flue gas thermostat to the

operating temperature (white mark upwards, approximately 90° to the right from the zero

position – it depends on the flue gas temperature required to stop the boiler after the fuel burns

out).

WARNING: The pull rod of the heat up flap has to be pushed backwards to close the

heat up flap. Otherwise the fan could get damaged.

For wood gasification in the boiler it is necessary to keep the reduction layer during the

operation (the layer of wood coal on the nozzle in the feeding chamber). Therefore it is

necessary to burn dry wood of a suitable size. When the wet wood is burned, the boiler does not

work as a wood gasifying boiler, the wood consumption rises, the output is not sufficient and

service life of the boiler and of the chimney is shortened.

When there is a prescribed chimney draught, the boiler works up to 70 % of its output even

without the fan.

Electromechanical boiler regulation

The boiler is regulated by the boiler thermostat placed on a boiler panel which controls the fan

according to the adjusted output temperature of water. The required operating boiler

temperature should be set on the boiler thermostat. The flue gas thermostat placed on a panel

serves to stop the fan after the fuel burns out. Set the flue gas thermostat to „0 °C“ when heating

up. When the fire is sufficient, set it to the operating position to let the fan run and to stop it after

the fuel burns out. The optimal position of the flue gas thermostat has to be found by

experience, adequately to the fuel used, chimney draught and other conditions. The output

temperature of water is indicated on thermo-manometer. The irreversible safety thermostat is

also placed on the front panel (the STANDARD and LAMBDA version).

Refilling the fuel

When refilling the fuel, open the feeding door. The heat up flap is opened at the same time. Do

not stop the fan. Always keep the feeding chamber full when heating up. Not to let the smoke

flow into the boiler room, refill the fuel after it is burned to approximately 1/3 of the feeding

chamber. Cover the glowing coal with a wide wood log and refill the fuel normally. Do not press

the fuel on the nozzle, otherwise it could get clogged and the parameters of burning would be

worse.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK DPX Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATTACK DPX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info