Bedienungsanleitung ATTACK DPX (Seite 42 von 92) (Englisch)

810499

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

• degree of flammability C2 normal combustibility (softwood (pine, spruce), chipboard,

solodur)

• degree of flammability C3 easily ignited (wood fibre boards, polyurethane, PVC, foam rubber,

polystyrene)

The sealing board or protection covering (on the protected item) must exceed the boiler edge

for at least 300 mm. Also other items from flammable materials must be protected in this way, if

they are placed near the boiler and it is not possible to keep the safe distance.

If the boiler stands on a flammable surface, it must be protected by an inflammable, heat

insulating mat, which exceeds the edge on the side of the feeding door and the ash tray door for

at least 100 mm. All materials of the A flammability degree can be used as an inflammable, heat

insulating mat.

The boiler must be placed in a such way ensuring sufficient space of at least 1 m from the front

and 0,5 m from the left (right) and rear side. It is necessary to leave the space of at least 1 m

above the boiler.

This space is necessary for basic operation, maintenance and eventual service of the boiler. It is

not allowed to place the boiler in dwelling premises (including corridors). There must be an

opening for the air inlet for burning of at least 200 cm

depending on the boiler output.

CAUTION! The items from flammable materials must not be laid on the boiler and in the

distance shorter than the permitted (safe) one. The boiler must be turned off, if there is

a danger of fire or explosion due to the work (e.g. work with painting materials, glues, etc.).

Air inlet

For correct operation of the boiler it is necessary to ensure sufficient air supply for burning.

There must be an opening for the air inlet for burning of at least 200 cm

depending on the

boiler output.

Boiler connection to the heating system

Only a trained technician can install and service the ATTACK DPX boiler. Before installing the

boiler, it is necessary to flush (to clean) the whole heating system. The system can be filled only

the water treated to the values under the STN 07 7401: 1992. Callosity of the water must not

excess 1mmol/l and concentration of the Ca²Ѐ must be lower than 0,3 mmol/l.

If these conditions are not kept, the warranty is not valid!

Chimney

Connection of the appliance to the chimney hole must be always done with permission of the

appropriate chimney sweep association. The chimney must generate sufficient draught and take

the flue gas out into the atmosphere under the all operating conditions.

Correct dimensions of the chimney hole are important the correct boiler function, because the

burning, output and boiler life-time are influenced by the draught. The chimney draught directly

depends on its diameter, height and roughness of the internal wall. It is not allowed to connect

any other appliance to the chimney, where the boiler is connected. Diameter of the chimney

must not be smaller than the connection part on the boiler. The chimney draught must achieve

the prescribed values, but it cannot be too high, not to decrease the boiler output and interrupt

the burning (flame). If there is too strong draught, install the throttle flap into the chimney hole

between the boiler and the chimney.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK DPX Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATTACK DPX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info