Bedienungsanleitung ATTACK EZ (Seite 11 von 28) (Englisch)

810552

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

| 11

CAST IRON FLOOR STANDING GAS BOILER

CONNECTING THE BOILER TO THE ELECTRICITY MAINS NOT FOR ATTACK P BOILERS

Boilers are plugged into the electrical socket of 230 V/50 Hz placed near the boiler, with a supply

cable ended with a plug. In line with the ČSN EN 60 335-1, the plug must be approachable after the

boiler is installed. The socket must be adequately protected by zeroising or grounding and it must be

connected in line with the ČSN 33 21 80. The boiler and other parts of installation must be grounded.

Installation of the socket, room thermostat, circulation pump and service of electrical boiler parts can

be carried out only by a person with proper electrotechnical qualiﬁcation, by the law No. 718/2002.

ELECTRICAL EQUIPMENT OF BOILERS

All the electroinstallation is placed on an insulating pad of the electrical board. On the front cover

there is a main switch, output switch (PLQ, KLQ), switch of failure unblocking (E, EZ), control button

of the boiler thermostat and thermomanometer. When the power supply fails, all the euipment

supplied with the power of 230 V is out of operation which means that a valve closes gas ﬂow to

the burners. The ﬂame of ignition burner (EKO, PLQ, P) is still burns and the boiler stays in a stand-

by mode. After the power supply starts again, the function starts automatically. Electrical installa-

tion is ready to connect the additional room thermostat, pump and switch contacts of three-way

valve. The room thermostat or the contacts of the three-way valve are connected after removing

the jumper on terminals 7, 8 and the circulation pump is connected to the terminals 3, 4, 5. By the

E boiler type is the room thermostat connected to the terminals 8, 9 and circulation pump to the

terminals 11, 12, 13. By the EZ boiler type is the room thermostat connected to the terminals 6, 7,

three-way valve to the terminals 3, 4, 5 and circulation pump to the terminals 12, 13, 14. Connection

of the room thermostat, circulation pump and three-way valve can be performed only by a person

with electrical qualiﬁcation by the law No. 718/2002.

START  PUTTING THE BOILER INTO OPERATION

1. Remove the door.

2. Plug the ﬂex cable into the electricity mains, the main switch is in the oﬀ position.

3. Open the gas supply to the boiler by a manual valve on the inlet pipe.

4. Set the required temperature of outlet water by knob of the thermostat.

5. The temperature is increased by turning the switch to the right (clockwise) and decreased by

turning the switch to the left (anticlockwise).

6. Press the control button of the gas combined electrical valve and hold it for 20 seconds. At the

same time press the button of piezo ignitor hardly for few times. Check the ignition burner

through the hole. ATTENTION – around the check hole there is a risk of burn when touch. Be

careful by work with the valve and piezo ignitor, not to get burned. Release the button of the

valve. The gas ﬂows into the ignition burner and the sensor of thermo-couple is heated by ﬂame.

If the ﬂame is extinguishes, the process of ignition must be repeated (EKO, PLQ, P). By the KLQ,

KLV and EZ versions, are the burners ignited automatically after switching the main switch and

setting up the boiler thermostat.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK EZ Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info