Bedienungsanleitung ATTACK KLV (Seite 7 von 28) (Englisch)

810550

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

| 7

CAST IRON FLOOR STANDING GAS BOILER

If there is a danger of approach of inﬂammable (explosive) gases or fumes to the boiler (e.g. by

PVC application), it must be put out of operation early including the burning ﬂame (EKO, PLQ, P).

SAFETY CONDITIONS

When installing a boiler, a safe distance of its surface from inﬂammable materials depending on

the degree of ﬂammability must be kept. Distances:

yfrom inﬂammable materials of B, C1, C2 categories 200 mm

yfrom inﬂammable materials of C3 category 400 mm

yfrom materials not tested by STN 73 0853 400 mm

EXAMPLES OF CLASSIFICATION OF THE BUILDING MATERIALS BY THE INFLAM

MABLE LEVEL:

yA category non-combustible (brick, blocks, concrete, tiles, mortar, plaster)

yB category very diﬃcult to ignite (heraklit, lignos, basalt boards)

yC1 category diﬃcult to ignite (beech, oak, wood-ﬁbre, werzalit, cardboard)

yC2 category normally ﬂammable (pinewood, solodur)

yC3 category easily ﬂammable (wood-ﬁbre boards, polyurethan, PVC, styrofoam)

If a boiler stands on the ﬂoor made from ﬂammable materials, it must be protected by incombus-

tible insulating plate exceeding boiler dimensions for at least in 150 mm. Solid materials of the A

category can be used as incombustible and insulating materials. Objects from ﬂammable materials

cannot be placed on the boiler nor in the distance shorter than 500 mm.

CONDITIONS TO KEEP THE ECOLOGICAL PARAMETERS

The boiler is set up and tested by the producer to ensure the optimum process of burning in line

with the ecological requirements. The boiler must be installed into the dry and dustless environ-

ment, without possibility to suck strange, aggressive materials or fogs through the air supply. Ask

the specialized company to take care about the the ﬂue gas exhaust. It is necessary to make the

annual tests and cleaning.

TECHNICAL DESCRIPTION EKO, PLQ, KLV, KLQ, E, EZ, P TYPES:

The body of boilers consists of cast-iron elements with the system of exchanger ribs, where the

ﬂue gas go into the collector and through draught breaker into the chimney. The pipes with screw

joints 1“ or 6/4“ (S, P) have to be connected to the heating system on the rear side of the body. In the

upper front in a copper sleeve there are emergency thermostat and sensors of boiler thermostat

and thermomanometer. In the rear bottom part there is the inlet and outlet valve and in the front

upper part there is a reverse valve with a sensor of the pressure gauge.

The boiler body is insulated by insulating material preventing the heat leakage into surround-

ings. The front wall is covered by protective metal sheet. After demounting the boiler skeleton and

draught breaker, it is possible to get to the combustion chamber, to check or to clean the exchang-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK KLV Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info