Bedienungsanleitung ATTACK Pellet 30 Automatic Plus (Seite 10 von 60) (Englisch)

810507

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Connection of appliance to chimney vent must always be done with agreement of the

appropri-ate chimney authority. Chimney vent must create sufficient draught and

reliably exhaust flue into atmosphere under all practically possible conditions. Correct

dize of the chimney vent en-sures correct boiler function. Chimney draught directly

depends on its diameter, height and roughness of its internal wall. Chimney vent must

be sufficiently insulated to prevent creation of condensate. Temperature of the area of 1

m under the chimney collar cannot be lower than 60°C. Any other appliance cannot

be connected to the chimney joined with the boiler. Diameter of chimney cannot be

smaller than boiler outlet. Chimney draught must achieve prescribed val-ues. However, it

cannot be too high, not to decrease boiler efficiency and not affect the combus-tion (not

to disturb the flame). In case of too strong draught i tis necessary to install

throttling flap between boiler and chimney.

• Information values of chimney diameter

• 20×20 cm min. height 7 m

•

∅

20 cm min. height 8 m



• 15×15 cm min. height 11 m

•

∅

16 cm min. height 12 m



•

Exact chimney dimension is determined by the STN 73 42 10. Prescribed chimney

draught is giv-en in the Technical parameters.



Examples of division of constructive materials by the grade of flammability:

•grade of flammability A – inflammable (brick, block, ceramic tiles, mortar, plaster)

•grade of flammability B – very difficult to ignite (heraclith, lignos, boards from bazart felt)

•grade of flammability C1 – hard flammable (beech, oak, plywood, wersalit, hardened

paper)

•grade of flammability C2 – medium flammable (pine, spruce chipboard, solodur)

•grade of flammability C3 – lightly flammable (boards from wood fibres, polyurethane,

PVC, foam rubber, polystyrene)

If boiler stands on the floor from flammable materials, it must be protected by inflammable

heat insulating pad, excessing boiler edge for 150 mm at least. It is possible to use

materials of the flammable grade A as inflammable and heat insulating mate-rials. Any

items from flammable materials cannot be placed on the boiler and in distance shorter

than 500 mm.

When placing boiler in the boiler room, there should be free space left of at least 1

m beyond and 0,5 m from the sides and rear part of boiler. Above the boiler, there should

be free space of at least 1 m. This space is necessary for ordinary operation,

maintenance and eventual boiler servicing..

ATTENTION: It is inadmissible to place the ATTACK PELLET 30 AUTOMATIC

Plus boiler in dwelling premises (including corridors)!

Air inlet

For correct boiler operation, it is necessary to ensure sufficient air supply for

combustion. Mini-mum area of the air inlet is 200 cm2.

Boiler connection into heating system

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK Pellet 30 Automatic Plus Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATTACK Pellet 30 Automatic Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info