Bedienungsanleitung ATTACK Pellet 30 Automatic Plus (Seite 20 von 60) (Englisch)

810507

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

DESCRIPTION OF BURNER FUNCTION

Normal start-up

• When thermostat gives instruction to burner, ventilator is started and photocell

controls flame. If there is no flame, then comes the instruction for test blow-through of

burner. After-wards, pellets start falling into burner within the period stated by control

system and ignition is activated. When the phase of fuel supply for ignition ends,

control system awaits flame signal from photocell.

• When photocell recognizes flame, small amounts of pellets are falling within the

transition period. Duration of this period depends on the output level set on burner.

Pellet supply is be-ing continually increased, unless it is adequate to the required

output.

• This amount is further supplied into burner, until the operation thermostat gives

instruction to stop.

• This signal stops pellet supply, while ventilator continues with air supply into burner.

• When photocell recognizes fuel burn-down, the burner blow-through begins.

• According to the adjusted delay, after fuel burn-down, burner cleaning begins – burner

grate moves out against scraper and ash with unburnt pieces fall through front side of

burner bot-tom into ash tray.

• After the grate moves back, the burner awaits new signal from thermostat.

ATTENTION! Grate drive unit is very strong and it may cause danger. Never put any

body parts or other foreign objects into burner, when it is operating.

Normal start, when there is still flame in burner

If photocell recognizes flame during the start-up phase (e.g. after short-time power failure),

con-trol system immediately begins transition period. Pellet burner continues in

operation as by normal start. (see above)

ATTENTION! Make sure, that sufficient flue gas temperature had been achieved. It

has to be at least 60 °C – one meter under the chimney top. Lower temperature

should be con-sulted with chimneyer. Flue gas temperature lower than 60°C

during the combustion process increases risk of chimney damage by

condensation.

USAGE OF PELLET BURNER

Pellet burner needs air for combustion. Thereby, boiler room must have opening for

air inlet of at least 200 cm2. Pellet burner must not be started before it is verified, that

smoke can freely flow through boiler and chimney into atmosphere. Pellet are supplied

into burner from external feeder, connected to pellet container. Feeder has to be installed

under the 45°angle to ensure the best function and uniform fuel supply. Feeder

should be able to supply approximately 10 kg of pellets per hour of continual

operation / requirement for pellet supply. Pellets must be stored in well ventilated

room without moisture, or in specially designed container.

ATTENTION! Burner consists from components of high quality, that must not

be re-placed with less quality spare parts. If components are replaced by

other than original spare parts, warranty expires.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK Pellet 30 Automatic Plus Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATTACK Pellet 30 Automatic Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info