Bedienungsanleitung ATTACK PLQ (Seite 15 von 28) (Englisch)

810548

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

| 15

CAST IRON FLOOR STANDING GAS BOILER

AFTER SET UP

The most simple regulation is to set up the operation thermostat correctly, depending on the

outside temperature according to the informative values which must be adjusted by the user by

his own experience and various ways of the source dimensioning, heating bodies, construction of

the building, etc.

The boiler works adequately to the selected mode. After reaching the required temperature of

heating water, the ﬂame on burners extinguishes and only the ignition burner burns (EKO, PLQ, P).

After it gets colder, the ﬂame is ignited automatically. With this way of regulation the cycles (on-oﬀ)

of the boiler change often, mainly in the transient times of seasons when the heating water tem-

perature is low, and there is excess output. Such operation mode is not good for the boiler and it

increases average consumption of gas. For these times we recommend to decrease the output for

PLQ, KLQ modiﬁcations, to prolong the boiler lifetime and to decrease the average gas consump-

tion. By the E, EZ modiﬁcations is the output decreased automatically.

REGULATION OF OPERATION

It is possible to use the additional regulation which is not included into the equipment of the

boiler. The installation must be done adequately to the project. It is also possible to use regulators

and room thermostats according to the temperature of the selected reference room or equither-

mal regulation of the heating water.

There is a wide range of room thermostats of domestic and foreign production from simple ones

up to programmable ones with daily or weekly cycle to regulate the room temperature. In this case

is the temperature of heating water stable and keeps the boiler in longer operating modes. Due this,

the producer recommends to install the mixing circle as a basic element to regulate the operation.

The regulation is done through mixing the hot water from the boiler with returning water in the

heating system. The water of the adequate temperature is prepared by mixing the water from the

boiler with return water and the heated object gets only the necessary amount of heat. Except of the

mixing device there are also the servo-gear and the electronic regulator. The mixing device can be

used separately, without automatic regulation by servo-gear. In this case it must be manually set to

a certain point of scale according to the estimated temperature. A suitable type and size is selected

by project maker as a part of complete additional regulation for automatic operation.

MARKING OF THE BOILER

The marking means the whole identiﬁcation of the boiler and it is in the form of a adhesive label

placed on the rear cover of the boiler. A brief summary of instructions and information about ma-

nipulation is on the label on the internal part of the boiler door.

SPARE PARTS

The producer keeps the particular parts of boilers as spare parts which are provided for guaran-

tee and post-guarantee service only to contract partners on the base of order or claim.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATTACK PLQ Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info