Bedienungsanleitung Audio-Technica AT-LPW40WN (Seite 13 von 15) (Englisch)

704637

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Troubleshooting

Problem Solution

The platter does not spin. • Is the AC adapter connected to the outlet? Connect AC adapter to the outlet.

• Has the AC adapter's plug come off? Check whether or not the plug is properly attached to the AC adapter.

• Has the belt slipped from the platter? Correctly place the belt on the platter.

• Is the belt placed on the motor pulley? Check that the belt is placed on the motor pulley correctly.

• Has the belt been damaged? Replace it with a new belt.

The platter spins, but there is

no sound or the volume is not

loud enough.

• Are the function settings and input for connected equipment (amplifier, etc.) selected correctly? Check

whether the settings for the connected equipment are correct.

• Is the stylus damaged? Check the stylus and replace it, if necessary.

• Is the stylus placed correctly on the body of the cartridge? Check the cartridge and adjust it, if necessary.

• Are the setting positions for the output selector switch correct? Check that the output settings are correct,

noting the following common problems and their causes:

- If there is no sound, or if the volume is not loud enough, the product is set to the “PHONO” position

and connected to the amplifier’s AUX/LINE input.

- If the volume is too loud or is distorted, the product is set to the “LINE” position and connected to the

amplifier's PHONO input.

• Is the tracking force set too heavy? Adjust the tracking force.

The stylus skips. • Is the tracking force set too light? Adjust the tracking force.

• Is the anti-skate set improperly? Verify anti-skate is set for same value as cartridge tracking force.

• Is the record warped? Check the record.

• Is the record scratched? Check the record.

• Is the stylus dirty? Excess build up around the stylus tip will effect tracking.

There is howling. • Is the product picking up excessive vibrations from the floor, surfaces of the walls, or nearby speakers?

Decrease the vibrations or mount the product on a surface that is not subject to the effects of vibrations.

• Is the product mounted on an unstable surface? Check whether the surface on which the product is

mounted is suitable.

There is noise when the record

is playing.

• Is there dust on the cartridge’s stylus tip? If dust is stuck to the stylus tip, clean it with a commercially

sold brush.

The sound when the record is

playing is either too fast or too

slow.

• Are the speed settings for the product correct? Use the control knob to select the correct speed for the

type of record being played.

Playing speed slows down or

there is irregular rotation.

• Is the belt stretched out? Replace it with a new belt.

Humming is heard during

playback.

• Is the ground line connected correctly? Make sure the ground line is properly connected.

• Is the headshell attached to the tonearm firmly? Make sure the locking ring is tight.

Dimensions

(Unit: mm)

420

340

116.9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audio-Technica AT-LPW40WN Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Audio-Technica AT-LPW40WN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info