Bedienungsanleitung Audio-Technica M3 - Wireless In-Ear Monitor System (Seite 9 von 118) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

704640

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

Frequency (Receiver)

Permits manual selection of a frequency. See How to Select a

Frequency, page 11.

Group (Receiver)

Permits selection of frequency groups with pre-coordinated channels.

See How to Select a Frequency, page 11.

User (Receiver)

Permits selection (optional) from among three user-created frequency

groups. See How to Select a Frequency, page 11.

Scan (Receiver)

Allows you to scan automatically for an available frequency. See How

to Select a Frequency, page 11.

Limiter (Receiver)

Limits output level to earphones. Choices are 3,2,1, OFF. Factory

setting is 3 (maximum limiting). Touch the Up/Down arrow buttons

to change the setting. When the setting you want to select is shown,

Hold the Set button. IMPORTANT: Leave limiter at setting 3. This

setting protects your hearing from unexpected signal peaks; it does

not protect your hearing from long-term exposure to high SPLs.

Squelch Control (Receiver)

Allows you to adjust squelch on receiver, eliminating unwanted

background RF noise. Maximum squelch setting (minimum range) is 2;

OFF is no squelch (maximum range). Touch the Up/Down arrow

buttons to change the setting. When the setting you want to select is

shown, Hold the Set button.

Mode (Receiver)

Permits changing the receiving mode from Mono to Stereo. Touch the

Up/Down arrow buttons to change the setting. When the setting you

want to select is shown, Hold the Set button. (See Output, below.)

Output (Receiver)

Allows you to switch headphones output between Mix and Stereo. In

the Stereo setting, the L1 signal goes to the left earphone; the R2

signal goes to the right earphone. In the Mix setting, a combined signal

from both the L/1 and R/2 inputs goes to both earphones. When the

setting you prefer is shown, Hold the Set button.

The Mode and Output menus are used together as follows:

Stereo Mode & Stereo Output

The Stereo/Stereo configuration is used as follows: the L/1 input signal

goes to the left earphone; the R/1 input signal goes to the right

earphone. Use the receiver’s balance control to adjust the stereo image.

See image A on page 14.

Stereo Mode & Mix Output

The Stereo/Mix configuration is used as follows: the signals from

both the L/1 and R/2 inputs go to both the left and right earphones.

Use the receiver’s balance control as follows: turn clockwise to

make R/2 louder and L/1 quieter; turn counterclockwise to make L/1

louder and R/2 quieter. (However you adjust the balance control,

both the left and right earphones will have the same total volume).

See image B on page 14.

Mono Mode (Output setting does not apply here; either Mix or

Stereo has the same result)

The Mono/Mix configuration is used as follows: there is only one

output from your mixer (connected to either the L/1 or R/2 input of

your transmitter). This signal will go to both left and right earphones.

When two-signal transmission is not required, use Mono Mode for

improved signal-to-noise performance. See image C on page 15.

Aux Level (Receiver)

Allows you to change the auxiliary input from mic level to line level.

When the setting you prefer is shown, Hold the Set button. Choose

mic level if you are connecting an ambient microphone (optional

Audio-Technica lavalier microphone) to the M3R Stereo Receiver’s

auxiliary input. Choose line level if you are connecting a click track or

other line-level source to the auxiliary input.

Note: If you connect a stereo source (such as an MP3 player) into

the M3R Stereo Receiver’s Aux Input, be certain to use a mono

adapter to protect your equipment from the DC voltage that is

applied to the ring of the stereo connector.

Mic Vol (Receiver)

If you have selected Mic Level (in the Aux Level menu above), the Mic

Vol menu allows you to adjust the volume of the ambient microphone

(optional Audio-Technica lavalier microphone or equivalent). 1 is the

lowest volume level; 16 is the highest volume level. When the setting

you prefer is shown, Hold the Set button. (Note: the Mic Vol menu does

not appear if you have selected Line Level in the Aux Level menu.)

Program (Receiver)

In the event that the preprogrammed frequency groups (available under

the Group menu) do not meet your requirements, Audio-Technica

allows you to program custom frequency groups. See How to Select a

Frequency, page 11.

Reset (Receiver)

Allows you to reset all receiver functions to their factory-default values.

Hold the Set button while “RESET” is displayed in the LCD window.

At the prompt OK? hold the Mode/Set button again. Factory-default

settings will be restored.

How to make setting changes on the M3R Stereo Receiver (continued)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audio-Technica M3 - Wireless In-Ear Monitor System Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info