Bedienungsanleitung Audiolab 8000AP (Seite 5 von 24) (Englisch)

496152

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

1: Preliminaries

Loudspeaker Placement

The 8000AP is a 7.1 channel processor. It allows the

connection of seven channels: front left, front centre, front

right, surround left, surround right, back left and back right,

plus a subwoofer channel.

All speakers (with the exception of the subwoofer) should be

arranged around your normal viewing/listening position.

Don’t worry if you are unable to position your speakers at

ideal distances from your preferred listening position, the

8000AP can be set up to take account of different distances.

The subwoofer can be placed almost anywhere, but we

recommend you experiment to obtain the best result.

Here is the Dolby Labs recommended speaker placement for

7.1 channel reproduction. Speaker placement is important

and dependent on room circumstances but this layout is a

very good starting point. If you are using a 5.1 or 6.1 layout,

adjust accordingly. (If you are using back channels, we

strongly recommend that you use a 7.1 layout with two rear

speakers rather than a 6.1 layout which only uses one.)

RbLb

90º

110º

135º

150º

22º

30º

LFE

Page 2Page 3

Unpacking

Placement

Before Starting

Unpack the product fully. The carton should contain:

The Audiolab 8000AP integrated amplifier

One IEC power cord suitable for your area

One Remote Handset with two AAA batteries

This instruction manual.

If any item is missing or damaged report this to your dealer as

soon as possible.

Retain the packing for future safe transport of your amplifier. If

you dispose of the packing, do so with regard to any recycling

regulations in your area.

Place the processor on a sturdy shelf or table.

The 8000AP is designed to run warm during normal

operation - even when put into standby.

Do not place anything on top of the unit. If you are using an

equipment rack ensure the 8000AP has sufficient space to

allow adequate ventilation and is on its own shelf.

Before you connect the 8000AP to the mains, ensure your

mains voltage corresponds to the rating plate on the rear of

the product. If in doubt, consult your dealer. If you move

house to an area which has a different mains voltage seek

advice from an Audiolab appointed dealer or a competent

service technician.

Make sure you locate the unit so that the front panel is in view

as otherwise the infrared-remote handset will not work.

Your 8000AP ’s performance is determined by the care you

take in setting your system up: not merely the processor but all

connected sources, amplification and loudspeakers.

Before setting up your processor, review all the handbooks for

your existing equipment and confirm that those items are set

up correctly. Have a variety of music and video software on

hand - you will need them. You will also need a tape measure,

and ideally a sound level (SPL) meter.

(

Phase

Gain and Efficiency

Phase is in a multi-channel environment. Make sure

that your loudspeakers are properly connected.

Some power amplifiers invert the phase - in a mixed system it

is just possible that even if all the loudspeakers are properly

connected one or more may be out of phase.

All Audiolab power amplifiers are phase coherent so even if

you are using different series, the loudspeakers will always be

in phase. provided they are properly connected.

Some subwoofers have adjustable phase control, others have

a phase inverting switch. You may have to use these controls

during the setup procedure. Consult the subwoofer

handbook for more information.

The 8000AP is adjustable across a wide range of volume

levels so differences in gain (in power amplifiers) and

efficiency (in loudspeakers) can be fully compensated. All

Audiolab amplifiers, irrespective of their output power feature

the same gain parameters.

Try not to set the subwoofer input volume too high or you may

overload the input. Again refer to your subwoofer handbook.

critical

If you are using different amplifiers:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiolab 8000AP Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info