Bedienungsanleitung Audiovox AA-RS30CS (Seite 13 von 20) (Englisch)

583736

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

1 Flash 10 or 15 Minute Run Timer Expired

2 Flashes Low or No Tach Signal (RPM)

3 Flashes Positive Or Negative Shutdown Wire Activated

4 Flashes Control Switch Moved to Off Position

5 Flashes RF shutdown, Remote signal received, or manual start trigger wire reactivated.

6 Flashes High RPM Signal Received

NOTE: 7 Flashes when attempting to remote start indicates that Tach Has Not Been Programmed.

TIMED START PROGRAM:

The Remote Start unit has the ability to start the vehicle automatically at timed intervals. This feature is useful in

extremely cold climates where starting the engine is the only means to keep the battery charged and fluids warm. The

operator has the option to have the unit start every 2 or 4 hours for a maximum of 48 hours. Factory pre-set is to start

at 4 hour intervals. To select 2 or 4 hour automatic start timer:

1. Start with the Enable switch (Red Handle) in the "On" Position.

2. Turn the ignition on then off.

3. Within 10 seconds of the key turning off, cycle the enable switch Off, On, Off, On ( 2 times) to select a 2 hour timed

start interval. Cycle the enable switch Off, On, Off, On, Off, On, Off, On (4 times) to select a 4 hour timed start

interval. The lights will flash 2X or 4X dependant upon 2 or 4 hour interval setting.

NOTE: Once selected, 2 or 4, this timer interval will remain in memory until it is manually changed. To change, the

above sequence will have to be followed.

TIMED START OPERATION:

To begin the start timer, within 10 seconds of turning off the ignition switch, activate the RF command to start 2 times.

(Press button two 4 times). The lights will flash 4 times. Indicating timed interval mode has been initiated. The vehicle

will automatically start every 2 or 4 hours as programmed. To cancel the timed start mode start the vehicle either by

RF or by the ignition key.

Multi Coil Pack Adaptor: (Optional)

The multi coil pack adaptor, (P/N 136B1400), is designed for use with vehicles having multiple ignition coils where a

single point tach signal is unavailable.

To use the adaptor, the Green/Black wires must connect to the negative side of the ignition coil(s).

1. For vehicles utilizing independent coils per cylinder, connect the three Green/Black leads to alternate coils. To

achieve optimum performance the coil signals must be evenly distributed. This is accomplished by first mapping

out the firing order of the engine in groups of as indicated below. Draw a circle around any of the columns. The

Green/Black wires should be connected to the negative (-) terminal of the respective cylinder number which

appears in any of the circles.

2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack. For 8

cylinder, four coil systems, connect to any of the three coils.

3. Connect the Yellow wire to a +12 volt ignition 1 source. This wire will have +12 volts with the ignition in the on and

start position and have 0 volts with the ignition in the off position.

4. Connect the Green wire to the (Green) or (Orange/Green) tach input of the Audiovox remote start unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiovox AA-RS30CS Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info