Bedienungsanleitung Audiovox AS9233ST (Seite 4 von 8) (Englisch)

583950

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

128-8604

4 of 8

2. Within 10 seconds begin to enter tenths digit of override code. (In this ex-

ample the code is 11, so press and release the push-button switch found on the glass

mounted receiver assembly one time).

3. Within 10 seconds of entering the last tenths digit, turn ignition “off then on”.

4. Within 10 seconds of turning the ignition switch on, begin to enter units digit

of override code. (In this example the code is 11, so press and release

the push-button switch found on the glass mounted receiver assembly one time).

5. Within 5 seconds after the last units digit is entered, turn the ignition switch

off, then on, and start your vehicle.

If the manual override code is entered properly, the unit stops sounding, the LED turns off,

indicating a successful override. The system is now disarmed and you can start and

operate your vehicle. The unit will allow three attempts to disarm via the manual override

sequence. If the code is not successfully entered within the three attempts, disarming with

the manual override switch will be locked for 10 minutes.

In many cases, to increase the security of your system, you may elect to change the manual

override code to a number that is more familiar to you, or simply to have a different code

than was pre-assigned from the factory. To Change the pre-assigned override code follow

the steps outlined below.

It is advised you read both sections under the headings “Programming Your Custom Over-

ride Code” and, “Custom Code Programming Example”, To completely understand the proce-

dure before beginning:

Programming Your Custom Override Code:

Unlike override switches easily found, and defeated, this system allows the con-

sumer to program a personal override code, offering a higher level of security. The system

comes from the factory with a pre-programmed override code of 11. To change this default

override code, do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency

override sequence. Turn the ignition switch to the on position.

2. Within 10 seconds, press and release the push-button switch found on the receiver

assembly 3 times.

3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.

(The siren or horn will beep and the lights will flash one time.)

4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing

and releasing the push-button switch from 1 up to 9 times.

5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then

on.

6. Within 10 seconds, begin to enter your chosen units digit by pressing

and releasing the push-button switch from 1 up to 9 times.

7. Finish by turning the ignition switch to the off position.

If the new code was accepted, the unit will report back the newly entered code, by flashing

the LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the

new code three times with a one second pause between each code, then the system will

begin arming. If the LED flash pattern reports the previously stored code, the new code

was not entered correctly. Please repeat steps 1 through 7 above considering the follow-

ing.

NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize

a 0 (Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for

more then 5 seconds during any of the above steps, the unit will revert back

to the last successfully stored code.

Custom Code Programming Example:

To Change the code from the factory pre-assigned code of 11 to “52” you

would do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency

override sequence.

Page 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiovox AS9233ST Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info