Bedienungsanleitung Audiovox Prestige Platinum APS 686T (Seite 14 von 20) (Englisch)

583910

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

128-7201

14 of 20

NOTE: When selecting Diesel mode, be certain that the intended vehicle has a true tach reference and be

certain to connect the tach input wire.

To program these selectable features:

1. Turn the ignition key to the ON position.

2. Press and release the pushbutton switch 3 times

3. Immediately turn the ignition key OFF, then back to ON.

4. Press and release the pushbutton switch 2 times.

5. Use channel one button on the transmitter to advance to the feature that you want to change. EXAMPLE

If you need to change programmable feature number 3, press and release button 1 on the transmitter 3 times

in succession. The parking lights will flash 3 times confirming that selected feature 3 can now be

programmed.

6. Use channel 3 button on the transmitter to change the selection of the programmable feature. If you are

not sure what the setting for any feature is, press channel 3 button one time, the parking lights will flash

one, two, three or four times indicating the features setting.

Note: Once you enter the feature programming mode, do not allow more that 15 seconds to pass between

steps, or the programming will be terminated.

2. Programming Tach Rate:

NOTE: All applications require that tach be programmed.

The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote

start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been

learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not

realize that the vehicle is running in certain instances reengage the starter motor.

The Remote Car Starter will learn the tach rate of most vehicle's single ignition coils, multiple coil packs,

and or single injector. To learn tach;

1. Turn the ignition key to the ON position.

2. Press and release the program pushbutton switch 3 times.

3. Immediately turn the ignition key OFF.

4. Press and hold the program pushbutton switch, then start the vehicle using the ignition key.

5. When the unit senses the tach signal, the parking lights will begin to flash.

6. Release the program pushbutton switch. The parking lights will turn on for 3 seconds to indicate that the

tach signal is stored and the unit is now out of the program mode.

3. Diagnostics:

1. Be sure that programmable feature number # 10 is set to the "Diagnostics On" mode.

2. Hold the program switch on, then turn the ignition key to the ON position.

3. The lights will flash, and number of flashes will indicate the reason for shutdown on the last remote start

attempt. The indications are as follows.

1 Flash Run Timer Expired

2 Flashes Low, or No Tach Signal

3 Flashes Positive Or Negative Shutdown

4 Flashes Control Switch Moved To Off

5 Flashes RF Shut Down, Remote Signal Received, or Manual Start Input Wire Reactivated.

6 Flashes High RPM Signal Received

7 Flashes Tach Has Not Been Programmed

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiovox Prestige Platinum APS 686T Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info