Bedienungsanleitung Audiovox Pursuit Series PRO 800 (Seite 7 von 12) (Englisch)

583761

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

128-6844

7 of 12

INTRUSION WARNING SIGNALS

This system will inform you if an intrusion attempt has occurred while you were

away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4

times and the parking lights will flash 3 times when disarming the system. Enter

the vehicle and observe the dash mounted LED to identify which zone was trig-

gered.

 If the LED is flashing one time...pause...one time...pause...etc., then an

intrusion attempt was made to the shock sensor, or an accessory

triggering device that may have been added to the system.

 If the LED is flashing two times...pause...two times...pause...etc., then

an intrusion attempt was made to a hood or trunk pin switch that was

added to the system, or to a light activated entry point if the alarm was

installed using the voltage sensing feature.

 If the LED is flashing three times...pause...three times...pause...etc.,

then an intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory and will

only be erased when the ignition key is turned on.

VALET SWITCH

The valet switch allows you to temporarily bypass all alarm functions, eliminating

the need to hand your transmitter to parking attendants or garage mechanics.

When the system is in valet mode, all alarm functions are bypassed, however the

remote panic feature and remote door locks will remain operational. To use the

valet mode, the system must first be disarmed either by using your keychain

transmitter, or by operating the manual override sequence.

1. From the disarmed condition, turn the ignition key to the on position.

2. Press and hold the valet pushbutton switch until the dash mounted LED,

turns on. The LED will remain on as long as the system is in valet mode.

3. To return to normal operation, press and release the push button switch any

time the ignition is on.

NOTE: Always remember to return the system to the NON VALET mode, after

servicing, to ensure that the vehicle remains protected at all times.

MANUALLY OVERRIDING YOUR SYSTEM:

USING THE VALET SWITCH MANUAL OVERRIDE

Your Security System can be disarmed without the use of the keychain transmitter.

This is necessary, since you will need the ability to operate your vehicle if the

transmitter is lost or its battery fails. If your system has been selected for Valet

Switch manual override as indicated on the last page of this manual, to by-pass

the alarm system.

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

3. Within 5 seconds, press and release the valet push button switch.

The alarm system will stop sounding and enter the disarmed mode. You can now

start and operate the vehicle normally.

Typically this override mode is used only if the transmitter has become inoperative.

You may elect to enter the VALET mode until repair or replacement of the transmitter,

after which, returning the system to the full operation mode is necessary. To do

so, see item 3 under the heading VALET SWITCH.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiovox Pursuit Series PRO 800 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info