Bedienungsanleitung Auna Silverhammer4 - 10006686 (Seite 14 von 22) (Deutsch, Englisch)

705688

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Notes on the power supply

• Connect the +12V power supply lead only after all the other leads have been connected.

• Be sure to connect the ground lead of the unit securely to a metal point of the car. A loose connection

may cause a malfunction of the amplier.

• Be sure to connect the remote control lead of the car audio to the remote terminal,

• When using a car audio without a remote output on the amplier, connect the remote input terminal

(REMOTE)to the accessory Power supply.

• Use the power supply lead with a fuse attached <7. 5A 2).

• Place the fuse in the power supply lead as close as possible to the car battery.

• Make sure that the leads to be connected to the +12Vand GND terminals of this unit are larger

than 10-Gauge (AWG-10) or have a sectional area of more than 5 (mm)

Precautions

• This unit is designed for negative ground 12V DCoperation only.

• Use speakers with suitable impedance.--2 to 16ohm (stereo).

• Do not connect any active speakers (with built~in amplier)to the speaker terminals of the nuit.

• Avoid installing the unit where:

- it would be subject to high temperatures such as from direct sunlight or hot airfrom the heater.

- it would be exposed to rain or moisture.

- it would be subject to dust or dirt. If your car is parked in direct sunlight and there is a considerable

rise in temperature inside the car, allow the unit to cool down before use.

• When installing the unit horizontally, be sure not to cover the ns with the ﬂoor carpet etc.

• If this unit is placed too close to the car radio, interference may occur. In this case, relocate the

amplier away from the car radio.

• If no power is being supplied to the master unit, check the connections.

• This power amplier employs a protection circuit to protect the transistors and speakers if the

amplier malfunctions.

• Do not attempt to test the protection circuit by covering the heat dink or connecting improperloads.

• Do not use the unit on a weak battery as its optimum performance depends on s good power supply.

•

For safety reasons, keep you caraudio volume moderate so that you can still hearsounds outside your car.

Protection circuit

This amplier is provided with a protection circuit that operates in the following cases:

- when the unit is overheated

- when a DC current is generated

- when the speaker terminals are short circuited.

The PROTECTOR indicator lights up in red and the unit will shut down.

If this happens, turn o the connected equipment, take out the cassette tape or disc, and determine

the cause of the malfunction, If the amplier has overheated, wait until the unit cools down beforeuse.

Installation

Before installation

• Mount the unit either inside the trunk or under a seat

• Choose the mounting location carefully so the unit will not

interfere with the normal movements of the driver and it will

not be exposed to direct sunlight or hot air from the heater.

• Do not install the unit under the ﬂoor carpet, where the heat

dissipation from the unit will be considerably impaired.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Auna Silverhammer4 - 10006686 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info