Bedienungsanleitung Auriol 2-LD3493-8 IAN 89492 (Seite 13 von 15) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

734401

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite



Display modes

Press A to select one of the display modes of the wrist watch:

Manually initiate radio reception

Radio time signal reception can be started manually.

Press A to select the date display mode.

Press and hold A for 3 seconds. The reception is started and the radio reception control symbol will appear

blinking on the display. Radio reception takes between 3 and 9 minutes to complete and can be interrupted by

pressing any button.

The radio reception control symbol will appear continuously on the display while the reception is successful.

date

day of

the week

time

zone

seconds



Changing the time zone

Press A to select time zone display mode.

Press and hold B for 3 seconds. Press A to select the correct time zone:

Uk = Greenwich Mean Time (UTC), GE = Central European Time (UTC+1), GR = Eastern Europe (UTC+2).

Confirm your selection by pressing B. The hands will automatically move to the appropriate time.

Manual time setting

Only use the manual time setting if radio signal reception is not possible. Should your watch display the incorrect

time, please proceed as described in the chapter "Troubleshooting" at the end of this manual.

Press A to select the date display mode. Press and hold B for 3 seconds.

The hours will blink on the display. Set the hours by pressing A and confirm your setting by pressing B.

The minutes will blink on the display. Set the minutes by pressing A and confirm your setting by pressing B.

The hands will automatically move to the appropriate time.

Day of the week language selection

Press A to select the day of the week display mode. Press and hold B for three seconds.

The set language will blink on the display. Select your preferred language by pressing A: En = English, DE =

German.

Confirm your selection by pressing B.

Reset and calibration

Replacing the battery, strong magnetic fields or strong vibrations may cause the hands to lose synchronisation with

the internal time. In this case the hands must be recalibrated. Ensure that the watch is displaying the date. If

necessary, repeatedly press A until the date appears.

Press and hold A and B for 5 seconds, until 'HP' appears blinking on the display.

Calibrating the minute hand

To set the minute hand exactly to the 12 o'clock (60 minute) position:

• Press and hold A. The minute hand will move forward and will continue to move until it is stopped by

again pressing A. Stop the minute hand shortly before it reaches the 12 o'clock position.

• Repeatedly press A briefly- the minute hand will move by one sixth of a minute each time A is

pressed. Move the minute hand exactly to the 12 o'clock position.

Now press B to continue to the calibration of the hour hand.



Calibrating the hour hand

A digit will appear blinking on the display. This digit must match the current position of the hour hand. Do not set the

actual current time! For example: If the hour hand is at the 5 o'clock position, the display must also show "5".

• Repeatedly press A to adjust the digit in the display to match the position of the hour hand.

Briefly press B to complete the setting process.

The watch will now start radio reception.

Water resistance

Water resistant up to 5 bar. The bar value

specifies the atmospheric overpressure

which is applied during testing (DIN

8310).

Strap Shortening Instructions

Your wristwatch strap may be shortened in two ways.



1. At the buckle (see fig. 1.)

Unlock the safety cover (if applicable) and open the buckle. The strap is held in position by a spring bar. The spring

bar can be compressed with a pointed tool to enable shortening of the strap. Move the strap to the desired position

and allow the spring bar to lock into place.

2. At the strap (see fig. 2)

Shortening of the strap can also be achieved by removing segments. Open the buckle and remove the spring bar as

described in part 1.

Place the wristwatch on a soft surface with the dial facing downward. The segments that can be removed are

marked with an arrow. Push a pointed tool into the opening on the backside of the strap and push the bolt out of the

strap in the direction of the arrow. Pull out the bolt (you may need to use tweezers).

The strap can now be disassembled.

Remove as many segments as necessary in the described fashion and reassemble the strap by pushing the bolt

inwards in the opposite direction of the arrow. Reassemble the buckle with the spring bar.

Replacement of battery

(2-LD3493-(2-5) = CR2032, 2-LD3493-(6-8) = CR1620)

Battery replacements must be performed by an expert to avoid damaging the case or gaskets.

Troubleshooting

If your watch displays an incorrect time, this can have different causes.

1.1.

1. The displayed time differs from the actual time by exactly one or more hours. The minutes are correct.

Restart radio reception first. See "Manually initiate radio reception".

The incorrect time zone may be set. Follow the instructions in the chapter "Changing the time zone".

If the problem persists, follow the instructions in the chapter "Reset and calibration".

2.2.

2. The time differs by one or more minutes and possibly hours.

Restart radio reception first. See "Manually initiate radio reception".

Follow the instructions in the chapter "Reset and calibration".

Auriol 2-LD3493-8 IAN 89492 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info