Bedienungsanleitung Auriol Z30237B (Seite 32 von 45) (Italienisch, Portugiesisch, Spanisch)

517791

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

32 GB/MT

Installing the LCD

radio-controlled clock

Note: You will need a drill, suitable assembly

material and a screwdriver for installation.

CAUTION! DANGER TO LIFE AND RISK

OF INJURY; RISK OF DAMAGE TO PROP-

ERTY! Please read the operating and safety instruc-

tions for your drill carefully.

WARNING!

DANGER TO LIFE! Please

ensure that you do not drill into any electrical wiring,

gas or water pipes in the wall. If necessary, carry out

checks with a wire, pipe and stud detector before

you drill into a wall.

Find a suitable place to install the radio-controlled

clock.

˽ Mark the drill hole on the wall.

CAUTION! DANGER OF INJURY! Refer to

the operating instructions for your electric drill.

˽ Drill the hole with a drill.

Insert a suitable dowel into the drill hole.

˽ Use a screwdriver to insert a suitable screw.

Hang the radio-controlled clock on the screw

using the mount

Inserting or replacing batteries

The battery symbol

appears in the LC dis-

play if the batteries are too weak. Make sure you

replace the batteries at the earliest opportunity.

The radio-controlled LCD wall clock starts to receive

the radio time signal as soon as the batteries are

inserted.

Note: Do not alter the position of the radio-controlled

clock during reception of the signal. This may disrupt

reception.

Radio time signal (DCF):

The DCF signal (time signal transmission) consists

of time pulses broadcast from one of the most accu-

rate clocks in the world. It is situated near Frankfurt /

Main, Germany.

Your radio-controlled clock receives these signals

under ideal conditions up to a distance of approx.

1,500 km around Frankfurt / Main. Reception of the

radio signal generally takes approx. 3–10 minutes.

If it does not work properly, restart the radio-

controlled clock. To do this, keep the WAVE

button

pressed for approx. 3 seconds.

Reception can be considerably impaired by obstacles

(e.g. concrete walls) or sources of interference (e.g.

other electrical devices). If necessary, change the

location of the radio clock (e.g. by putting it near a

window) if you have problems with reception.

Operation

Reception of DCF radio signal

The radio-controlled clock automatically starts to

search for the DCF radio signal. The radio icon

on the LCD indicates that the clock is searching for the

radio signal.

Note: Reception of the radio signal may be seriously

disrupted in reinforced concrete buildings (see “Set-

ting up Devices”).

It is also possible to start reception of the DCF radio

signal manually on the clock.

Press and keep pressed the WAVE button

for longer than 3 seconds. The LCD radio-con-

trolled wall clock attempts to receive the DCF

radio time signal. This process takes several

minutes and is indicated in the LC display by a

ﬂashing radio symbol

Note: If the radio-controlled clock cannot pick up

the DCF radio signal on account of an error or the

distance from the transmitter, etc., it is also possible

to set the time manually. As soon as reception of

the DCF signal is successful, the manual settings

are overwritten.

Before Initial Use / Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Auriol Z30237B Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Auriol Z30237B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info