Bedienungsanleitung Austroflamm BonoXtra (Seite 8 von 20) (Deutsch, Englisch, Französisch, Italienisch)

694276

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Bono/Bono Xtra 6 english

Floor load capacity

Make sure that the load capacity of the supporting

construction is sufficient to carry the weight of the

entire unit

, before the heating unit is installed.

Combustion air

Being the user of the stove you must take care of a

sufficient combustion air supply. Sealed-up windows

and doors may not allow a sufficient combustion air

supply or disturb the draught behaviour of your stove.

Please ensure the additional supply of fresh

combustion air if necessary. For details please

consult your specialist retailer

Stove pipe connection

For your own safety stringent laws apply for

connecting the stove pipes to the chimney. Your

professional dealer or distributor knows these laws.

Please have your certified retailer carry out the

connection of your stove

2. CORRECT OPERATION OF YOUR STOVE

Approved fuels

Dry, well cured and natural wood (hardwood

preferred), wood briquettes.

Maximum amount of fuel

Maximum amount of fuel to be added: 1,3 kg wood or

briquettes. Larger amounts of fuel can lead to

overheating and thus damage the stove.

Clean burning

The wood must be dry (relative wood moisture

< 15%) and untreated and the right amount of wood

must be burned in order to ensure a clean fire that

releases only small amounts of emissions.

Making a fire

For the correct and safe operation of your stove

please pay attention of the chimney developing the

necessary feed pressure. This must especially be

considered before the initial operation (or e.g. after

the summer heating break) and during the mid-

season heating periods (e.g. at strong wind, etc.).

If there is not enough feed pressure, please light only

some paper or small kindling first, in order to “warm

up” the stove and the chimney.

Fully pull out both levers for the combustion air and

the grate (position “AUF” fig. 2, also fig. 3).

Place 2-3 logs (approx. 0,9 kg in total) crossways in

the combustion chamber with sufficient distance from

each other (min. 2 cm), on top of that place some

softwood chippings and some ignition aid and light.

Close the door!

Fig. 3: before lighting

We recommend to let the first load burn down without

changing the air lever position.

As soon as no visible flames are left (only embers in

the combustion chamber), you can put another load

of logs (approx. 1,3 kg) in the combustion chamber if

desired.

When reloading the stove please repeat the

procedure as mentioned under “first lighting”: air lever

position on “AUF” (= open), open door carefully, place

logs, close door.

After a few minutes, when the logs burn well on all

sides (bright, high flames), you can adjust the heat

output with the air lever (lever on max. position “AUF”

= maximum heat output), the flames should be yellow

and never look blueish or have black tips (otherwise

add more air) – see fig. 4. Never close air supply

completely during operation.

symbol figures

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Austroflamm BonoXtra Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Austroflamm BonoXtra

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info