Bedienungsanleitung Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II (Seite 64 von 122) (Englisch)

815458

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

9 | Installation instructions EN Operating manual Fireplace inserts slied flat + II

9.11 Ceiling above the fireplace insert

Fig.14: Ceiling above fireplace insert

If the cavity above the fireplace insert reaches as far as the

room ceiling (8), then the latter must be protected if:

• it consists of flammable components

• it serves as a bearing component

The thermal insulation layer (11) (dimension G) must be ex-

ecuted in compliance with the normal regional installation

standards.

8 Room ceiling

11 Heat insulation layer

9.12 Floor in front of the fireplace insert

The floor in front of the fireplace insert must be made of flammable material. Minimum dimensions of

this non-flammable area: forward at least 50cm, to the sides at least 30cm.

9.13 Fire protection

Fire protection within the radiation area

The minimum clearance (see Technical Data) to components made of flammable construction materi-

als or flammable components as well as furniture must be observed in front and on either side of the

firebox opening! For II series models the clearance applies to the front and rear.

Fire protection outside the radiation area

From the outer surfaces of the cladding of the open fireplace insert a distance of at least 5 cm must be

maintained from components made of flammable construction materials or flammable components

and from built-in furniture. The clearance space must be so open to the air current that an accumula-

tion of heat cannot occur. Components which only cover small areas of the cladding of the open fire-

place insert (such as floors, butt-joined wall cladding and insulation layers on ceilings and walls) can be

brought up to the cladding without any gap.

9.14 Heat insulation layers and materials

Insulation layers must be made of heat insulating boards of construction material class A1 as per DIN

4102 Part 1 with a maximum application temperature of at least 700°C and a bulk density of more

than 80kg/m³. The insulation material must be marked with the appropriate insulation material code

number as per AGI-Q 132. Only the insulation materials which are listed in the following table may be

used. If other insulation materials are used for the insulation layers, these must have an appropriate

DIBT approval (German Institute for Structural Engineering Berlin) (e.g.: Promat calcium silicate

thermal insulating board “Promasil950KS”, Wolfshöher thermal insulating board “Prowolf”, Wolf-

shöher thermal insulating board “Vermilite2000”, Thermax thermal insulating board “Ther-

maxSN400”). For building external walls and ceilings to be protected that have a U-value below

0.4W/m², additional rear ventilation (see technical rules of the Stove- and Air Heating Constructors As-

sociation) will be necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info