815458
95
Zoom out
Zoom in
Vorherige Seite
1/122
Nächste Seite
Operating manual Fireplace inserts slied flat + II EN 11 | Installation
95
1
3
2
Fig.69: Removing the parts
6) Remove centre stone tension support (1).
7) Remove the two M6x12 hexagon head screws (2).
8) Remove primary air cover (3).
ðNow InsertControl can be installed.
1
Fig.70: Installing the installation kit
In the following illustration the 363000 installation kit has
been installed in the left-hand version.
Depending on the appliance, installation kit and left- or
right-hand assembly situation, for installing the mounting,
other screws will have to be removed and installed again.
You can find this in the illustrations showing the assembly
situations of your stove/installation kit and in the detailed
drawing in the installation kit.
9) Install the installation kit (1) as shown.
ðAfter installing the installation kit, check the free
movement of the air regulator.
10) To do so, move the air regulator several times from
the minimum position to the maximum position.
Should there be no free movement of the air regu-
lator, check the following:
ðHas the installation kit been correctly installed.
ðAre the screw joints on the air regulator disc ex-
cessively tightened?
If the air regulator can be easily adjusted, the assembly of
the connection between installation kit and control unit can
be continued.
1
2
3
Fig.71: Installing the control unit
11) Remove the two M10x1 (1) and the M5 nut with flange
(2) and the spacer connecting plate (3).
For the connection between control unit and installation kit
you will require the following part from the installation kit:
2 x Taptite hex. LKS M5x10
2 x flange Bowden cable
Torx screwdriver (not included in the scope of delivery)
The installation point of the control unit must be chosen so
that the following items are guaranteed:
The ambient temperature of the control unit must not
exceed 50°C.
The control unit must be accessible.
A maximum of 2 curves must be laid with the Bowden
cable.
The curve radius of the Bowden cable must not be smal-
ler than 100 mm.
95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II

Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II Bedienungsanleitung - Deutsch - 124 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info