Bedienungsanleitung Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II (Seite 98 von 122) (Englisch)

815458

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

11 | Installation EN Operating manual Fireplace inserts slied flat + II

Calibration: The calibration (see above) of the controls is carried out when the controls are connected

to the mains or the WLAN is changed, but only if the flue gas temperature is below 80 ° C. In the pro-

cess the control software detects where the positions 0% and 100% shutter opening are on its fireplace

insert. After the controls have detected the two maximum positions, they run to the 0% shutter open-

ing (if the correct program has been chosen) and switches into the Standby phase.

This process requires approximately 10 minutes. Should the flue gas temperature be above 80°C, no

calibration run is carried out. The controls use the data from the last calibration run that was carried

out.

The programming of the controls includes various “Eco” and “Normal” combustion curves. Each of

these two modes is available with the “sliding opening” and “sliding closing” function.

Program overview

Selection wheel Mode Function

Position 0 - Shutter opening, always 60%

Position 1 Normal sliding opening

Position 2 Eco sliding opening

Position 3 Normal sliding closing

Position 4 Eco sliding closing

Selecting the program

Fig.76: Unplugging the power supply

1) Remove power supply from the socket.

2) Remove the three screws and open the control unit

housing.

Fig.77: Selecting the program

On the circuit board is a selector switch (1) that by default is

set to position “0”.

3) Select program by setting the arrow of the selector

switch to position 1, 2, 3 or 4 (see “Program Overview”

table.

4) Before closing the controls again, carry out a fresh cal-

ibration by plugging the power supply back in.

ðIf you have selected the correct “sliding closing” or

“sliding opening” function, after the calibration the

controls must complete close the shutter.

ðShould you notice that you have chosen the wrong

program, you can change this in the service menu

of the app.

APP

The InsertControl function can be monitored using the app on iOS and Android Smartphones. To do

so, first load the “InsertControl” app from the iTunes Store or Google Play on to your Smartphone.

When it is connected to the circuit, InsertControl creates a WLAN with the name “ABR_xxxxxxx”

(xxxxxxx = serial number of the controls). You must connect your Smartphone to this network (pass-

word: 12345678). After the app is started, the connection is automatically established.

If desired you can then connect the app to another WLAN (in the app’s settings menu). Please note

that a new calibration run for the controls will then be started.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II Seite 98

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info