Bedienungsanleitung Autotek TA1400 (Seite 10 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

701390

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

AUDIO SIGNAL CABLES

WheninstallingtheaudiocablesbetweentheRCAoutputsoftheheadunitandtheRCAinputsoftheamplier,

the audio and power supply cables should, if possible, not be routed along the same side of the vehicle. We

recommend a separated installation, e.g. routing the power cable through the cable channel on the left side

and the audio cables through the cable channel of the vehicle on the right side or vice versa. This prevents

interferences due to crosstalk into the audio signal.

INPUT SENSITIVITY

OPERATING ELEMENTS

TurntheGAINcontroller(Fig.1,7)oftheampliertotheMINposition.Thenturnthevolumecontrollerofthe

head unit to 80 - 90% of its full setting. Now turn GAIN clockwise until you hear some distortion. Then turn back

the GAIN (Fig. 1,7) slightly until you hear a cleaner sound.

VARIABLE HIGH PASS / SUBSONIC FILTER

WiththeHPF/SUBSONICcontroller(Fig.1,6)youcanadjustthelowercross-overfrequency,tolteroutthe

very low frequencies to relieve the subwoofer or to generate a bandpass signal. If you don’t want to use this

function, turn the controller (Fig. 1,6) to the very left to the 20 Hz position.

NOTE: The adjusted value of the HPF/SUB SONIC (Fig. 1,5) should not be higher than the adjusted value of

the LPF controller (Fig. 1,4). Otherwise no sound will be audible.

VARIABLE LOW PASS FILTER

Set the desired cross-over frequency by using the controller LPF (Fig. 1,4). Thus to that only the frequencies

belowthechosencross-overfrequencywillbeampliedandthesubwooferplaysmorepreciselyandefcient.

SIGNAL OUTPUTS FOR ADDITIONAL AMPLIFIERS

The input signal on the LINE INPUT jacks (Fig. 1,8) will be routed in stereo to the output jacks LINE OUTPUT

(Fig.1,9).ThustheLINEOUTPUTjackallowstheconnectionofaadditionalamplier.

X-OVER SWITCH

TheX-OVERswitchdeterminesthedesiredoperatingmodeoftheamplier.

LPF/BPF:Lowpasslter,thefrequencyrangeislimitedupwardly,adjustablebythecontrollerLPF(Fig.1,4).

The controller HPF/SUB SONIC (Fig. 1,6) acts in this mode as a subsonic lter and limits the frequency

downwards (bandpass function). NOTE: If this controller is turned to a higher value than the LPF controller, no

sound is audible.

HPF:Highpasslter,thefrequencyrangeislimiteddownwardly,adjustablebythecontrollerHPF/SUBSONIC

(Fig. 1,6).

FULL:Fullrangemode,theentirefrequencyrangeisamplied

BASS LEVEL REMOTE CONTROLLER

With the included bass level cable remote controller you are able to adjust the bass level e.g. out of the driver’s

seat.

VARIABLE BASS EQ

With the BASS EQ controller (Fig. 1,3) you are able to adjust the bass level from 0 - 12 dB.

Attention: Use the BASS EQ wisely!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Autotek TA1400 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info