Bedienungsanleitung Autotek TA4150 (Seite 10 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

701389

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

AUDIO SIGNAL CABLES

When installing the audio cables between the RCA outputs of the head unit and the RCA inputs of the amplier,

the audio and power supply cables should, if possible, not be routed along the same side of the vehicle. We

recommend a separated installation, e.g. routing the power cable through the cable channel on the left side

and the audio cables through the cable channel of the vehicle on the right side or vice versa. This prevents

interferences due to crosstalk into the audio signal.

INPUT SENSITIVITY CH1&2 + CH3&4

OPERATING ELEMENTS

Turn the GAIN controller (Fig. 1,6 and 1,8) of the amplier to the MIN position. Then turn the volume controller

of the head unit to 80 - 90% of its full setting. Now turn GAIN clockwise until you hear some distortion. Then

turn back the GAIN slightly until you hear a cleaner sound.

VARIABLE HIGH PASS FILTER CH1&2 + CH3&4

If the amplier is to be used for mid-range/tweeter loudspeakers, set the switches X-OVER (Fig. 1,3 and 1,9)

to HPF. Then set the desired cross-over frequency on the HPF controller (Fig.1,2 or 1,10). Thus to that only the

frequencies above the chosen cross-over frequency will be amplied. This effectively minimizes distortions and

overloads at lower frequencies. A good point to start is at 125 Hz.

If you use loudspeakers (>20 cm) set X-OVER (Fig.1,3 or 1,9) to FULL. In this case, the HPF controllers

(Fig.1,2 or 1,10) are without function.

VARIABLE LOW PASS FILTER CH3&4

If the amplier is used to drive a subwoofer, set the switch (Fig. 1,3) to „LPF“. Set the desired cross-over fre-

quency by using the controller LPF (Fig. 1,4). Thus to that only the frequencies below the chosen cross-over

frequency will be amplied and the subwoofer plays more precisely and efcient.

SWITCHABLE BASS EQ CH3&4

By using the BASS EQ switch (Fig. 1,5) you are able to increase the bass level by 6 or 12 dB at 45 Hz.

Attention: Use the BASS EQ wisely!

HIGH LEVEL INPUTS

The HIGH IN (Fig. 1,1 and 1,11) is suitable to connect the amplier inputs with speaker wires, if your head

unit is not equipped with pre-amplier RCA outputs. Extend therefor every regarding speaker cable from your

head unit with appropriate speaker cables from your car audio retailer to the mounting location of the amplier.

Then connect the each matching loudspeaker cable with the cables of the included HIGH IN jack like described

below.

ATTENTION: Never use the High Level Input and the RCA inputs at the same time. This may damage the

amplier seriously. The loudspeaker cables of the HIGH IN must have no contact to the ground (GND) by any

means.

grey = speaker - right - positive

brown = speaker - right - negative

white = speaker - left - negative

green = speaker - left - positive

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Autotek TA4150 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info