Bedienungsanleitung Avenli 12024 (Seite 4 von 21) (Deutsch, Englisch, Holländisch)

765046

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

RE-20-GB(V1) RE-20-GB(V1)

It is absolutely essential to select a suitable site for your pool BEFORE attempting to

ll it with any water. Please select a set-up site which strictly conforms to the following

guidelines:

Guide1. Ensure that the area is rm, at (no bumps or mounds of earth) and extremely level, with a grade not exceeding

3° of slope at any point in the set-up area.

Guide2. Make sure that the area you have selected to set-up the pool is completely free of sticks, stones, sharp objects or

other foreign debris.

Guide3. Select an area that is not directly underneath overhead power lines or trees. Additionally, make sure that the pool

set-up area does not contain underground utility pipes, lines, or cables or any kind.

Guide4. If a ground cloth is provided with your pool kit, its use is highly recommended. The ground cloth will help protect

the pool liner from damage due to weed growth, sharp objects, and debris.

Guide5. If at all possible, choose an open location on your property that is exposed to direct sunlight. This will help to

warm your pool.

WARNING:

Pools installed on inadequately level surfaces are subject to leak-

ing, forming irregularities, or collapse, which can result in property damage or

serious injury for those in or around the pool area!

WARNING:

Do not use sand during setup process. If it appears that there is a

need for use of a “leveling agent”, then your set-up site is likely unsuitable. FAIL-

URE TO OBEY THIS WARNING MAY RESULT IN SERIOUS PERSONAL INJURY.

CAUTION:

Please choose your set-up area carefully, as lawn and other desir-

able vegetation underneath the ground cloth(If applicable) will die. Furthermore,

try to avoid setting the ground cloth(If applicable)in areas prone to aggressive

plant and weed species, as they may grow through the ground cloth(If applica-

ble).

CAUTION:

The pool must be accessible to a 110 or 230-volt AC outlet pro-

tected by a Ground Fault Circuit Interrupter (GFCI). The pool should be set no

closer than 2 m. to the power source, but no further than the length of the lter

pump cord. Under no circumstances should an extension cord be used to extend

the range of the connection.

+3°

Bumpy,Sloping Ground-INCORRECT

Flat,Level Ground-CORRECT

PART3-SITE SELECTION PART4-SET UP THE POOL

Step1. ACCOUNT FOR ALL PARTS.

Remove all the parts from the carton(s) and place them on the ground in the location where they are to be assembled

Check each part according to “PART REFERENCE” .Make sure all the pieces to be assembled are accounted for.

IMPORTANT: Do not start assembly if any pieces are missing. For replacement pieces call the Consumer Service

telephone number in your area.

The number of persons required for installation: 2 adult at least.

Total installation time except the time for site preparation and water lling :

45 minutes for size 14’x9’x39.5’’

Step2. INSTALL DRAIN VALVES COVER AND STOPPER

Make sure that outer drain plug is inserted into the outer drain cap and drain valve cover is screwed on tightly.Plug the con-

nection holes with the stoppers. (The out drain plug changes according to different size of pool.)

STOPPER Out Drain Plug A Out Drain Plug BDrain Vavle Cover

Step3. INSTALL HORIZONTAL BEAM

BEAM A BEAM A

For all kinds of pool , the combination is A-A.

Slide combined beams into sleeve,the hole on the beams should face outwards.

Step4. INSTALL T-JOINT(FOR TYPE A)

1. Use the connection end of the T-Joint to

connect the adjacent horizontal tubes.

2. Insert the Pin into the hole of connected

horizontal tube and T-Joint rmly.

3. Install the vertical leg cap onto the vertical leg.

4. Insert the vertical leg into the T-Joint through

the belt.

5. Insert the pin into the hole of T-Joint and

Vertical Leg.

TIP: If you can’t nd the hole on the horizontal

tube or vertical leg please rotate the tubes until

the pin meets the hole.

BELT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Avenli 12024 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Avenli 12024

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info