Bedienungsanleitung Avenli 17726 (Seite 18 von 39) (Deutsch, Englisch, Holländisch)

765067

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

MFP-20-GB(V1)

PART7-IN-SEASON POOL

MAINTENANCE AND WATER CARE

your local after sale service center if you want to get advice on any repair during the life of the pool kit.

4. If applicable, check your lter-pump cartridge every two weeks (or more frequently during periods of heavy usage) to verify

whether it needs to be cleaned or replaced. If your cartridge is no longer white in color, attempt to spray it clean with a strong

blast of water from your garden hose. If your cartridge cannot be cleaned in this manner, the cartridge must be replaced. Failure

to frequently clean and/or replace your cartridges will affect the effectiveness of your lter pump and could shorten its useful life.

5. If your pool system included a cover, try to keep your pool covered at all times when not in use. This will help keep the wind

and other elements from depositing dirt and debris in your pool, and will also prevent excess rainwater from overlling your pool.

6. Remind your family and friends to always hose or rinse off any dirt or tanning oil from their hands, feet, and body prior to

entering the pool.

7. It’s necessary to monitor the bolts and hardware of the pool (eg. rust stain) when possible.

8. Once your pool has been lled with water for the season, take note if your pool becomes overlled due to rainwater or ac-

cidental overll. If this should occur, it is important to drain or bale out the excess water as soon as possible. If it is an inatable

ring pool, the water level should never be higher than the bottom edge of the inatable ring.

PART8-TROUBLE SHOOTING

Repair Patch Instructions

(Small pinhole and small puncture leaks can be repaired with the included repair patch)

a) Locate the leak place.

b) Deate the air.

c) Clean the area surrounding the leakage and wipe up all water from the surface.

d) Take out the repair patch, cut it into required shape and size, which should be larger than the leaking area, put the

patch on leaking area and press tightly.

e) Wait 30 minutes for open-air drying of the repaired position.

If the damage is too big, we recommend using a Silicone or rubber based glue for repair.

Repair Glue Instructions

1 Locate the leak place.

2 Deate（if necessary）,and drain thoroughly

3 Clean the area surrounding the leakage and wipe up all water from the surface.

4 Thoroughly clean the area surrounding the leak .Cut a piece of repair material in round shape, which should be

larger than the damaged area.

5 Gluing (need to purchase adhesive separately) one side of the material patch to the repair area. Please notice the

material patch need to be applied glue evenly.

6 Put the patch on the damaged area and press tightly. Wait 12 hours for drying. After patch has dried, apply glue

around the edges for a complete seal (dry 4 hours) swimming pool storage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Avenli 17726 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info