Bedienungsanleitung Avenli 290732 (Seite 15 von 23) (Englisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

765051

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

SFP8-20-GB

www.JLeisure-Global.com

28 SFP8-20-GB

www.JLeisure-Global.com

Location of

control valve Functions Water ow direction

Filter Normal ltering to rinse the pool

Water ows through the lter bed

where the sand lter pump lies

and then enters the pool

Backwash Reverse-direction water ow to

rinse the lter bed

Water ows through the lter bed

where the sand lter pump lies

and is then directly discharged

from the drain outlet.

Rinse

This function is used for rst

startup. Sand in the sand tank

is rinsed and the sand bed after

backwashing is leveled.

Water ows through the lter bed

where the sand lter pump lies

and is then directly discharged

from the drain outlet.

Drain

Discharged directly from the drain

outlet, used to lower water level

or discharge water from the pool

Discharged directly from the

drain outlet of the sand lter

pump without passing through

the lter bed

Recirculation Circulates pool water without

passing through the lter bed.

Water ows directly into the pool

through the control valve of the

sand lter pump without passing

through the lter bed

Closed Closed water ow between the

lter and the pool /

Note: During the operation of the sand lter

pump, check the pressure reading of the

manometer.

Generally, when the pressure of the

recommended sand lter pump is less than

0.2bar (3psi) (green area) , it runs normally.

Note: You must make sure that maintenance

begins only after the sand filter pump is

unplugged. Otherwise serious risks such as

personal injury and even death may occur.

Note: Record the reading of the manometer

during the operation of the sand lt er pump.

When the manometer shows a pressure

of 0.2bar (3psi) or higher, please clean up

the sand bend or replace the sand. Use

"backwash" and "rinse" functions.

Note: regular rinsing according to use

situation is recommended.

Long-term storage and storage in winter

Using the product in a frozen pool may damage the product and invalidate the

quality warranty. If the product has to be used with antifreeze, propylene glycol

may also be used. Propylene glycol is a nontoxic chemical unharmful to any plastic

parts. Other types of antifreeze are highly toxic and may be harmful to the product’s

plastic elements.

1.Before discharging the water or repostioning of the pool, make sure the discharge

direction is towards the discharging ditch and away from the home. Review local

regulations for special water treatment requirements.

2.Switch off the product and remove the power plug.

3.After emptying, remove all connected sand filter pumps, corrugated tubes and

lter hoods on the pool wall.

4.Unscrew the drain valve (8) in an anticlockwise direction to completely empty

water inside the body. The drain plug is at the bottom of the body.

5.Dry the parts of the sand lter pump and corrugated tubes.

6.Lubricate the seal rings and washers in the order below for long-term storage.

7.The best practice for product storage is to dry the parts and motor and replace

them in the original package. To avoid shrinkage or corrosion, do not cover or wrap

the motor with a plastic bag.

8.Please store the motor and parts in a dry place at 32°F (0°C) ~104°F (40°C).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Avenli 290732 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Avenli 290732

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info