Bedienungsanleitung Avenli 290732 (Seite 10 von 12) (Französisch)

765051

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

SFP8-20-GB

www.JLeisure-Global.com

18 SFP8-20-GB

www.JLeisure-Global.com

Note: During the operation of the sand lter

pump, check the pressure reading of the

manometer.

Generally, when the pressure of the

recommended sand lter pump is less than

0.2bar (3psi) (green area) , it runs normally.

Note: You must make sure that maintenance

begins only after the sand filter pump is

unplugged. Otherwise serious risks such as

personal injury and even death may occur.

Note: Record the reading of the manometer

during the operation of the sand lt er pump.

When the manometer shows a pressure

of 0.2bar (3psi) or higher, please clean up

the sand bend or replace the sand. Use

"backwash" and "rinse" functions.

Note: regular rinsing according to use

situation is recommended.

Long-term storage and storage in winter

Using the product in a frozen pool may damage the product and invalidate the

quality warranty. If the product has to be used with antifreeze, propylene glycol

may also be used. Propylene glycol is a nontoxic chemical unharmful to any plastic

parts. Other types of antifreeze are highly toxic and may be harmful to the product’s

plastic elements.

1.Before discharging the water or repostioning of the pool, make sure the discharge

direction is towards the discharging ditch and away from the home. Review local

regulations for special water treatment requirements.

2.Switch off the product and remove the power plug.

3.After emptying, remove all connected sand filter pumps, corrugated tubes and

lter hoods on the pool wall.

4.Unscrew the drain valve (8) in an anticlockwise direction to completely empty

water inside the body. The drain plug is at the bottom of the body.

5.Dry the parts of the sand lter pump and corrugated tubes.

6.Lubricate the seal rings and washers in the order below for long-term storage.

7.The best practice for product storage is to dry the parts and motor and replace

them in the original package. To avoid shrinkage or corrosion, do not cover or wrap

the motor with a plastic bag.

8.Please store the motor and parts in a dry place at 32°F (0°C) ~104°F (40°C).

Diagnosis of Problems and Solutions

Problems Checking Solutions

The motor can not be

started normally

Power plug not properly

inserted

Leakage protection

disconnected

Motor overheated or

overloaded

Causes motor to stop

Make sure the power cord is inserted

into the 3-core grounded metal

receptacle.

Reset circuit breaker. If the problem

persists, the power system may be

defective. Power off immediately and

confer with an expert.

Allow the motor to cool naturally and

start it again.

Filter

Unable to rinse the pool

No sand in the body

Location error of the control

valve

Excessive dirt in water

Filter barrel blocked

Sand filling Refer to sand filling

instructions

The control valve rotates to the filter

position

to prolong the running time

Clean the lter barrel

The filter is unable to

discharge water or the water

ow rate is too slow

There is blockage at the

inlet

There is an air leakage at

the gap of the inlet

Excessive dirt in water

Filter medium is blocked by

impurities

The pool is connected with

a cleaning device

Check and clear away the blockage in

the water pipes

Tighten the nozzle nuts and check the

damaged point of the nozzle and water

height

Clean the lter screen

Backwash

Disassemble the cleaning device

connected to the pool

Filter fails to run Water level is too low

Filter screen is blocked

Air leakage from the inlet

pipe

Motor or blade is blocked

Inject water to adjust water level

Clean the lter screen in the pool

Tighten the nozzle and check the

damaged point

Replace the ttings

Water leakage on the control

valve or upper cover

The seal ring of the body is

lost or too dirty

The control valve retainer

is not tightly secured

ordamaged

Remove the upper cover of the control

valve and sleeve the seal ring of the

body

Clean the seal ring of the body with a

water pipe

Tighten the screw with a screwdriver

Replace the ttings

The manometer fails to run The inner wall of the

manometer is blocked

The manometer is damaged

Remove the manometer from the

control valve and clear away the

impurities on the inner wall

Replace the ttings

Sand enters the pool The sand particles are too

ne

Use 20# quartz sand only

Particle size of the sand is 0.45-0.85mm

Or replace the sand

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Avenli 290732 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Avenli 290732

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info