Bedienungsanleitung AVTech - Velleman CAMCOLBUL24N (Seite 5 von 20) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

621855

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

CAMCOLBUL24N

V. 02 – 27/06/2013 5 ©Velleman nv

5. Overview

Refer to the illustrations on page 2 of this manual.

camera

sunshield

lens

camera bolt

IR LEDs

position bolt

light sensor

bracket

power supply

fuse

on/off switch

power adjustment switches

power LED (green)

camera connector

mains connector

monitor connector

hardware setup

to monitor

monitor connection

AC power cord

to camera

coaxial power supply

6. Installation

Refer to the illustrations on page 2 of this manual.

1. Choose a location for the camera, keeping the following guidelines in mind:

o Do not install the camera in locations where extremely high or low temperatures or excessive

vibrations may occur.

o Avoid mounting the camera near strong electromagnetic fields.

o Do not aim the camera at the sun or other extremely bright objects.

o Do not install behind a glass (or other) window as this will impact image quality.

2. Mount the mounting bracket [7] on a wall or ceiling with the 3 included screws.

3. Screw the camera on the bracket with the camera connection screw [5]. Note that the camera has

two mounting holes on either side, for wall or ceiling mounting.

4. Point the camera towards the field of interest and secure it by turning the butterfly nut [6].

5. The other side of the RG58U cable must be connected to connector [F] of the coaxial power supply.

6. Connect a monitor (not incl.) to connector [G] (cable not incl.).

7. Plug the mains connector [C] in the mains (230 V / 50 Hz).

8. Switch on the coaxial power supply with switch [A]. The status LED [B] turns green.

9. In case of a blown fuse [D] in the power supply, replace it with a 250V/2A fuse.

7. Adjusting Zoom and Focus

Refer to the illustrations on page 3 of this manual.

1. Locate the hex head screw at the bottom of the camera (see arrow).

2. Release this screw with the included Allen wrench and slide the housing towards the front of the

camera. The focus [a] and zoom [b] magnets become visible.

3. First adjust the zoom magnet [b]. Slide it upwards to zoom in (longer distance, smaller viewing

angle); slide it downwards to zoom out (shorter distance, wider viewing angle).

4. Then adjust the focus magnet [a]. Slide it upwards or downwards to adjust focus and make the

images sharper.

5. Slide the housing back in place and secure it with the hex head screw. Do not apply excessive force

on the screw.

8. Adjusting current settings

Refer to the illustrations on page 3 of this manual.

 You can adjust the power setting of the current between the power supply and the camera.

 Use the dip switches [E] on the back of the power supply to adjust the current.

 Possible settings are: 100 mA – 200 mA – 280 mA – 340 mA - 450 mA.

 The corresponding dip switch settings are as follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AVTech - Velleman CAMCOLBUL24N Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info