Bedienungsanleitung AVTech - Velleman CAMCOLBUL35 (Seite 7 von 47) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

621859

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

CAMCOLBUL35

V. 01 – 10/03/2014 7 ©Velleman nv

AREA NO 0–7

To define up to 8 areas. Select the desired area and use the settings below.

 STATUS: select ON to activate the selected masked area; select OFF to deactivate

the selected masked area.

 HORIZON SIZE: set the width [a] (in pixels) of the

masked area.

 VERTICAL SIZE: sets the height [b] (in pixels) of the

masked area.

 HORIZON MOVE: sets the distance (in pixels) from the

left side of the screen [c] for the masked area.

 VERTICAL MOVE: sets the distance (in pixels) from the

top of the screen [d] for the masked area.

7.11 Motion Detection

Use this function to see motion detection during live monitoring. You can define up to 4 separate areas

for motion detection. If the camera detects motion in an area, the outer edge of that area will ‘flash’.

Menu: DIRECTION

SENSITIVITY

Set the motion detection sensitivity. With a higher sensitivity, slighter movements will

be detected. Available options for sensitivity: WEAK (weak); LOW (low); MIDDLE

(medium), and HIGH (high).

AREA NO 0–3

To define up to 4 areas. Select the desired area and use the settings below.

 STATUS: select ON to activate the selected detection area; select OFF to deactivate

the selected detection area.

 COLOR: set the colour of the detection area. The outer edge of the area will flash in

this colour when the camera detects motion.

 HORIZON SIZE: set the width [a] (in pixels) of the

detection area.

 VERTICAL SIZE: sets the height [b] (in pixels) of the

detection area.

 HORIZON MOVE: sets the distance (in pixels) from the

left side of the screen [c] for the detection area.

 VERTICAL MOVE: sets the distance (in pixels) from the

top of the screen [d] for the detection area.

7.12 Language

Use this function to set the language of the OSD menu.

8. Troubleshooting

No image

Check the power supply voltage and polarity. Check if all cables are connected properly. Check if the

correct input channel is selected on the monitor.

Interference/ripples in the image

Interference/ripples can have many causes. Check if the power supply is stable. Keep the camera’s video

and power cables away from existing mains and data cables. Use good quality cables only. If the camera

and monitor are powered from sources with different grounds, this may cause ground loops. In this case,

install a ground loop corrector, or power the camera and the monitor from the same source.

Picture background colour changes continuously

The electromagnetic field from fluorescent lamps may cause colour roll in the image. Either reduce the

number of fluorescent lamps, or increase the distance between the camera and the lamps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AVTech - Velleman CAMCOLBUL35 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info