621958
5
Zoom out
Zoom in
Vorherige Seite
1/50
Nächste Seite
NVR3
V. 02 01/12/2014 5 ©Velleman nv
Rear panel
eSATA
Connect to a storage device that supports the eSATA interface. For example, an external hard
disk or a disk array.
Note: Make sure that the disk array supports Linux® to ensure proper functioning.
HDMI
Connect to a monitor that supports high-definition video output (HDMI port).
Note: Use an appropriate adapter (not incl.) to connect a monitor with VGA or composite
connectors.
INTERNET
(WAN)
Connect to internet via an 8P8C network cable.
1 4 (LAN)
Connect to local IP cameras via an 8P8C network cable. The LAN ports support PoE (Power over
Ethernet), therefore no power adapters are required for the cameras.
On/off switch. Set to I to switch the NVR on. Set to O to switch off.
DC48V IN
Connect to the power supply adapter (incl.).
7. Connection Diagram
Refer to the illustrations on page 2 of this manual.
Note: This configuration method applies to ETS cameras.
The NVR will automatically configure the IP address of an ETS camera connected by LAN if:
The default IP configuration method of the camera is DHCP.
The camera is powered on before the NVR is powered on.
You can connect up to 4 IP cameras.
A
IP camera
F
Install a HDD in the NVR before connecting it to
the IP cameras.
B
Alarm I/O + magnetic contact. Refer to the user
manual of the IP camera for connection.
G
external hard disk or disk array (eSATA)
C
8P8C network cable
H
HDMI monitor
D
remote control
I
IP camera, laptop, iPhone, iPad, Android device,
etc. via internet
E
on/off switch
J
48 VDC power adapter
Connecting the IP Camera (Plug and Play)
1. Connect the camera to a LAN port. Make sure the camera is switched on.
2. Switch on [E] the NVR.
3. Wait until the camera is configured automatically and the images appear on the monitor.
8. User Interface
8.1 NVR Access
1. Connect a USB mouse (included) to the mouse port on the NVR front panel, and check if there is a
mouse icon on the screen, indicating the USB mouse is detected properly.
2. Move your mouse to enter the DVR password with the password keypad. The default user name and
password are both admin.
The status will change from (key lock) to (unlock).
Note: You can configure four different user levels with different access privileges in the main menu
(SYSTEM) > ACCOUNT. For more information, refer to the full user manual on the included CD-ROM.
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für AVTech - Velleman NVR3 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info