Bedienungsanleitung Axiair Elica - Alba Pyramide (Seite 18 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

496217

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

suction speed (power) - RED LED LIGHT

suction speed (power) - RED LED LIGHT (FLASHING)

Note: The 4

suction speed (power) stays on for 5 minutes,

after which the suction motor will position itself on the 2

speed.

If pressed again, the suction motor will switch off (stand-by).

Grease filters need cleaning: FLASHING GREEN LED light

(read instructions found under “Reset and configuration for

filter saturation signal”)

Coal filters must be cleaned or replaced: FLASHING

ORANGE (amber) LED light (read instructions found under

“Reset and configuration for filter saturation signal”)

Note: The reset procedure may be activated by both the

control panel and the remote control.

Center light check

The center light may be switched on and off by pressing the

T2 button on the control panel.

Side light check (when scheduled)

The side lights may be switched on and off by pressing AND

HOLDING DOWN the T2 button on the control panel.

HOLDING DOWN the button, besides permitting to switch the

hood on and off, it also regulates the light intensity given from

the lights.

Note: The switching on and off functions (and regulating

function) alternate.

The regulation of the light intensity is not available for hoods

with neon lights.

Reset and configuration for filter saturation signal

Switch on hood to any speed (see above paragraph “Suction

speed (power) selection”)

Reset grease filter saturation signal (FLASHING GREEN

LIGHT on control panel)

First proceed with filter maintenance as described in

corresponding paragraph.

Press and hold down (for more than 3 seconds) the T1 button

on the control panel, the LED light will stop flashing indicating

that the signal reset has been carried out, the hood will switch

off.

Reset coal filter saturation signal (FLASHING ORANGE

(amber) LED light)

First proceed with filter maintenance as described in

corresponding paragraph.

Press and hold down (for more than 3 seconds) the T1 button

on the control panel, the LED light will stop flashing indicating

that the signal reset has been carried out, the hood will switch

off.

Coal filter saturation signal disactivaction (for particular

applications)

Switch off hood (see above paragraph “suction speed (power)

selection”).

Press and hold down (for more than 5 seconds) the T1 button

on the control panel, the LED light will start flashing GREEN

indicating that the coal filter saturation signal has been

disactivated.

In order to reactivate the coal filter saturation signal, repeat

operation, the LED light will flash ORANGE (amber)

Using the remote control

The remote control is able to control all the functions of the

hood:

Select the suction speed (power)

Control the central light

Control the lateral lights

Reset e configure the saturation of the filters signal

Selecting the suction speed (power):

Press the "◄" key or the "►" key until you see the symbol

relating to the “Select the suction speed (power)” function.

Press the “+” key or the “-” key or the "■" key respectively to

increase or diminish or switch off (stand-by) the speed

(suction power).

Controlling the central light:

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Controlling the central light” function on the

remote control.

The central light can be switched on and off in two ways:

1. Press the “+” key or the “-” key respectively to switch the

central light (ON) or (OFF).

2. Press the "■" key to change the state of the light from

(OFF) to (ON) or vice versa.

Controlling the lateral lights:

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Controlling the lateral lights” function on the

remote control.

Press the "■" key to change the state of the lateral lights from

(OFF) to (ON) at maximum intensity and viceversa.

Press the “-” key to diminish the intensity of the lateral lights

until switching them off.

Press the “+” key to increase the intensity of the lateral lights.

Resetting and configuring the saturation of the filters

signal

Switch the hood on at any speed (see paragraph above

“Selecting the suction speed (power”).

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Resetting and configuration of the saturation of

the filters signal” function on the remote control.

Resetting the anti-fat filter saturation signal (GREEN LED

FLASHING on the control bar)

First proceed with the maintenance of the filter as

described in the corresponding paragraph.

Press the “+” and “-” keys contemporaneously for about 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Axiair Elica - Alba Pyramide Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info