Bedienungsanleitung Axiair Platinum - Wave (Seite 22 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

496210

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Reset grease filter saturation signal (FLASHING GREEN

LIGHT on control panel)

First proceed with filter maintenance as described in

corresponding paragraph.

Press and hold down (for more than 3 seconds) the T1 button

on the control panel, the LED light will stop flashing indicating

that the signal reset has been carried out, the hood will switch

off.

Reset coal filter saturation signal (FLASHING ORANGE

(amber) LED light)

First proceed with filter maintenance as described in

corresponding paragraph.

Press and hold down (for more than 3 seconds) the T1 button

on the control panel, the LED light will stop flashing indicating

that the signal reset has been carried out, the hood will switch

off.

Coal filter saturation signal disactivaction (for particular

applications)

Switch off hood (see above paragraph “suction speed (power)

selection”).

Press and hold down (for more than 5 seconds) the T1 button

on the control panel, the LED light will start flashing GREEN

indicating that the coal filter saturation signal has been

disactivated.

In order to reactivate the coal filter saturation signal, repeat

operation, the LED light will flash ORANGE (amber)

Command panel disassembly.

Remove equipment from electrical grid.

Remove grease filter.

Disconnect connectors.

Extract command panel by lifting it with a small screwdriver or

similar tool.

Fig. 22

Using the remote control

The remote control is able to control all the functions of the

hood:

Select the suction speed (power)

Control the central light

Control the lateral lights

Reset e configure the saturation of the filters signal

Selecting the suction speed (power):

Press the "◄" key or the "►" key until you see the symbol

relating to the “Select the suction speed (power)” function.

Press the “+” key or the “-” key or the "■" key respectively to

increase or diminish or switch off (stand-by) the speed

(suction power).

Controlling the central light:

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Controlling the central light” function on the

remote control.

The central light can be switched on and off in two ways:

1. Press the “+” key or the “-” key respectively to switch the

central light (ON) or (OFF).

2. Press the "■" key to change the state of the light from

(OFF) to (ON) or vice versa.

Controlling the lateral lights:

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Controlling the lateral lights” function on the

remote control.

Press the "■" key to change the state of the lateral lights from

(OFF) to (ON) at maximum intensity and viceversa.

Press the “-” key to diminish the intensity of the lateral lights

until switching them off.

Press the “+” key to increase the intensity of the lateral lights.

Resetting and configuring the saturation of the filters

signal

Switch the hood on at any speed (see paragraph above

“Selecting the suction speed (power”).

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Resetting and configuration of the saturation of

the filters signal” function on the remote control.

Resetting the anti-fat filter saturation signal (GREEN LED

FLASHING on the control bar)

First proceed with the maintenance of the filter as

described in the corresponding paragraph.

Press the “+” and “-” keys contemporaneously for about 3

seconds. The LED stops flashing, indicating that the resetting

of the signal has been accomplished.

Resetting the carbon filter saturation signal (ORANGE

(amber) LED FLASHING)

Note! The reset of the carbon filter saturation signal is

normally deactivated. To activate it, see under paragraph

“Activating the carbon filter saturation signal”.

First proceed with the maintenance of the filter as

described in the corresponding paragraph.

Press the “+” and “-” keys contemporaneously for about 3

seconds. The LED stops flashing, indicating that the resetting

of the signal has been accomplished.

Deactivating the carbon filter saturation signal (for

special applications)

Switch the hood off (see paragraph above “Selecting the

suction speed (power)”).

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Resetting and configuration of the filters

saturation signal” function on the remote control.

Press keys “+” and “-” contemporaneously for about 3

seconds. The LED flashes in GREEN to indicate that the

carbon filter saturation signal has been deactivated.

To reactivate the carbon filter saturation signal, repeat the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Axiair Platinum - Wave Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info