Bedienungsanleitung Axis 214 PTZ - Network Camera (Seite 29 von 53) (Englisch)

615957

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

AXIS 214 PTZ

Include pre-trigger buffer - images stored internally in the server from the time immediately preceding the

trigger. Check the box to enable the pre-trigger buffer, enter the desired length of time and specify the

required image frequency.

Include post-trigger buffer - contains i

mages from the time immediately after the trigger. Configure as for

pre-trigger.

Note:

If the pre- or post-buffer is too large for the internal memory, the frame rate will be reduced and no image will be uploaded. If

this occurs, an entry will be created in the unit's log file.

Continue image upload (unbuffered) - enable the upload of images for a fixed length of time. Specify the

length of time for the uploaded recording, in seconds, minutes or hours, or for as long as the trigger is

active. Finally, set the desired image frequency to the maximum (the maximum available) or to a specified

frame rate. The frame rate will be the best possible, but might not be as high as specified, especially if

uploading via a slow connection.

Scheduled events

A Scheduled event can be activated at preset times, in a repeating pattern on selected weekdays.

How to set up a scheduled event

This example describes how to set the AXIS 214 PTZ to send an email notification

with saved images from

a set time:

1. Click Ad

d scheduled on the Event types page.

2. Enter a descriptive name for the event, e.g. Scheduled email.

3. Set the Priority (High, Normal or Low).

4. Set the Activation Time parameters (24h clock) when the event is to be active, e.g. start on Fridays

at 18.00 with a duration of 62 hours.

5. Set the When Activated... parameters i.e. set what the AXIS 214 PTZ is to do at the specified time

e.g. send uploaded images to an email address.

6. Click OK to save the event in the Event Types list.

Please see the online help for descriptions of each available option.

Motion Detection

The AXIS 214 PTZ can be configured for motion detection. This feature is used to generate an alarm

whenever movement starts (or stops) in the image. The AXIS 214 PTZ can use a maximum of 10

Include/Exclude windows.

• Include

windows target specific areas within the image

• Ex

clude windows are areas to be ignored within the Include window

Once configured, the motion detection windows will appear in

a list when motion detection is set to trigger

an event. See How to set up a triggered event above.

Notes:

• Using the motion detection feature may decrease overall performance in the camera.

• Motion detection will not function while the lens is moving (i.e. pan, tilt, zoom)

Configuring Motion Detection

With reference to the motion detection parameters

in the table below, follow these instructions to create a

motion detection window.

1. a) For AMC: Check the radio button Con

figure Include Windows to set the type of window. Click

the New button. A new window called DefaultWindow appears over the image. Select the name in

the list of windows and rename the window.

b) For the Java applet: Click the Add Window button. Check the radio button Include or Exclude

to define the type of window. Select the tab for the window and rename the window.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Axis 214 PTZ - Network Camera Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info