Bedienungsanleitung Axkid Rekid (Seite 10 von 67) (Deutsch, Englisch, Französisch, Spanisch, Polnisch, Schwedisch)

768000

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

To adjust the angle of the child restraint, press the recline adjustment lever (G) to select one of

the three reclining positions. Always choose the most upright position as possible, however

your child must be able to hold their head up on its own, and there should be enough recline to

ensure your child’s head does not fall forward when sleeping. The rule of thumb is that the older the

child grows, the more upright the seat can be installed. Please note that once the installation of the

Rekid is complete, it will be somewhat more reclined as it sinks into the vehicle’s seat from tightening

seat belts and tether straps.

Open the belt lock-o clips (K) on both sides of the Rekid child restraint. Fully lengthen the seat

belt until the lap section of the belt is at least 70-80cm (27-32 inches) long. Feed the seat belt

through the seat belt slot (D), between the seat cover and seat body until the belt comes out

through the seat belt slot on the other side. If you prefer, you can instead feed the seat belt through

the seat belt slot (D), then over the top of the seat belt cover and then through the seat belt slot on the

other side.

Insert the seat belt tongue into the vehicle’s seat belt buckle. Pull the seat belt until all slack is

removed along the seat belt route. Secure both the lap and shoulder belt in the lock-o closest

to the vehicle’s seat belt buckle.

In the lock-o on the opposite side, only the lap belt should be secured.

Fastening The Vehicle Seat Belt

Some vehicles may already be tted with anchorage points at the base of the front seat rails, or, if

installing in the front passenger seat, in front of that seat.

If your vehicle does not have these anchor points, the supplied lower anchor straps must be

used.

For installation in the back seat, feed the buckle end of the anchor strap through either the rear

of the front seat rails, or the hinge of the front seat. The anchoring point needs to be as close

to the oor as possible. In doing so you should always insert the buckle of the anchor strap

through the closest appropriate slot in the strap to create a slip knot then pull tight. This needs to be

repeated on both sides to create two anchor points.

When installing Rekid in the front passenger seat the lower anchor straps must be attached

to the front gliding tracks so the anchor points will be located along the front edge of the

passenger seat.

Pull out the upper tether strap from the belt housing (N) to an appropriate length.

Check that the white marking on the strap (i) is visible. If not, you can try crossing the straps

over (ii) to give them some extra length to enable the white marking to be visible.

Attaching The Tether Straps

11b

12b

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Axkid Rekid Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info