Bedienungsanleitung Axton c 109 (Seite 31 von 60) (Deutsch, Englisch, Französisch)

167491

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

AMPLIFIER LOCATION & MOUNTING

The mounting location of the power amplifier will have a large

effect both on its ability to dissipate the heat generated during

normal operation through the heat sink and on the possible triggering

of its internal overheat protection shut-off circuit. Any mounting po-

sition allowing for a good air stream across the cooling fins of the

amplifiers heatsink will improve cooling and long-term stability

dramatically.

With the AXTON amplifier series the most efficient ventilation is

achieved when the units are installed standing up!

Therefore select a suitable location that is convenient for mounting and

accessible for wiring and offers sufficient ventilation for cooling. As your

amplifier features no controls for normal operation, it may be mounted

away from the dashboard, i.e. under a car seat or in the trunk. However,

make sure the unit is not exposed to excessive dust, direct sunlight,

humidity, water, oil or other fluids that may enter the amplifier.

The amplifier should be mounted to a solid surface that will ensure

a vibration-free mount. Once the location is selected, use the unit

as a template for the marking of the mounting holes which should also

be pilot-drilled before mounting of the amp is carried out.

Secure the amplifier using the four screws. Avoid to let the amp-

lifier get into contact with metal parts of the vehicle. This helps

to prevent unwanted ground loops.

WIRING TIPS

Please note: wrong power or signal connections may damage the am-

plifier and other components connected to it. Therefore, please read

this manual carefully before the connection of any power, signal and

speaker leads is done.

The wire routing is critical for noise-free performance. For best results,

please follow the general wiring guidelines listed below (for details see

section B, E, F and G of this manual).

For audio signal connections you should always use double or

triple shielded quality RCA cables.

Signal, speaker and power cables should always be kept as short

as possible:

™ Speaker and power cables may be cut to fit the actual length

required.

™ Shielded RCA/signal cables should never be cut and respliced,

as they will loose their protective shielding effect at those points

where they have been cut. If the signal cable is too long, make an

S-type loop (never a coil loop) in the centre of the cable to take-up

the excess length.

Never route any low level/signal cable near or parallel to speaker

outputs/speaker cables, amplifier power cables or high energy

ignition wires.

Use power cable with the recommended cross section (see

section E). Small cross sections are reducing the output power,

are causing distortions and may be triggering the overheat protection

of the amplifier.

C109-509 Manual DEF.indd 31C109-509 Manual DEF.indd 31 15.02.2005 15:30:31 Uhr15.02.2005 15:30:31 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Axton c 109 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info