Bedienungsanleitung Axton c 508 (Seite 27 von 52) (Deutsch, Englisch, Französisch)

165860

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

AMPLIFIER LOCATION

The mounting location of the power amplifier will have a large ef-

fect both on its ability to dissipate the heat generated during

normal operation through the heat sink and on the possible triggering

of its internal overheat protection shut-off circuit.

Any mounting po-

sition allowing for a good air stream across the cooling fins of the

amplifiers heatsink will improve cooling and long-term stability

dramatically.

With the AXTON Amplifier Series the most efficient ventilation is

achieved when the units are installed standing up!

Therefore select a suitable location that is convenient for mounting and

accessible for wiring and offers sufficient ventilation for cooling. As

your amplifier features no controls for normal operation, it may be mo-

unted away from the dashboard, i.e. under a car seat or in the trunk.

However, make sure the unit is not exposed to excessive dust, direct

sunlight, humidity, water, oil or other fluids that may enter the ampli-

fier.

The amplifier should be mounted to a solid surface that will en-

sure a vibration-free mount. Once the location is selected, use the

unit as a template for the marking of the mounting holes which

should also be pilot-drilled before final securing with the provided

screws is carried out.

Secure the amplifier using the four screws. Avoid to let the am-

plifier get into contact with metal parts of the vehicle. This helps

to eliminate unwanted ground loops.

WIRING TIPS

Please note: wrong power or signal connections may damage the am-

plifier and other components connected to it. Therefore, please read

this manual carefully before the connection of any power, signal and

speaker leads.

The wire routing is critical for noise-free performance. For best results,

please follow the general wiring guidelines listed below (for details see

section B, E, F and G of this manual).

For audio signal connections you should always use double or tri-

ple shielded quality RCA cables.

Signal, speaker and power cables should always be kept as

short as possible:

™ Speaker and power cables may easily be cut to fit the actual

lengths required.

™ Shielded RCA/signal cables should never be cut and respliced, as

they will loose their protective shielding effect at those points whe-

re they have been cut. If the signal cable is too long, make an S-

type loop (never a coil loop) in the centre of the cable to take-up

the excess length.

Never route any low level/signal cable near or parallel to speaker

outputs/speaker cables, amplifier power cables or high energy

ignition wires.

Use power cable with the recommended cross-section (see

section E). Small crosssections are reducing the output power,

are causing distortions and may be triggering the overheat protection

of the amplifier.

C208 408 508 Manual UK-D-F 23.07.2003 19:30 Uhr Seite 27

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Axton c 508 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info