Bedienungsanleitung Axton c 609 (Seite 26 von 44) (Deutsch, Englisch, Französisch)

167495

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

CONTROLS & ADJUSTMENTS

C609 5-Channel System Amplifier

The AXTON C609 is a powerful 5-channel system amplifier. One single

C609 allows for an easy-to-install, speaker-dedicated amplification

of a complete 5-channel speaker system, i.e. with two stereo pairs of

independently controlled satellite speakers (front and rear) and one

mono subwoofer.

The integrated, separately adjustable HIGHPASS and LOWPASS cross-

over filters of the C609 enable you to drive the connected speakers in

the specific frequency range where they will perform best.

Dashboard, door and rear shelf speakers of 10-16cm diameter will never

have a good low-end bass reproduction anyway. Therefore the C609

front and rear satellite channels will only be playing in the midbass

and mid/high frequency range. This so-called highpass filtered or HPF

amplification mode aIso puts less electrical and mechanical ‚strain‘ on

the speaker units, resulting in an increased power handling capacity. The

subwoofer output will only receive lowpass filtered (LPF) signals resul-

ting in the subwoofer only playing in the low-end bass frequency range

without any unwanted‚ booming‘ into the mid/high frequencies.

CROSSOVER FREQUENCY SETTINGS

HIGHPASS FRONT & REAR, LOWPASS SUB

Before you can effect the respective input sensitivity or gain LEVELs

you first have to select the system appropriate crossover frequencies.

For best results all crossover adjustments should usually be effected

by ear.

For appropriate crossover frequency selection, all tone controls (Bass,

Mid, Treble, Sub) and all fader and balance controls etc. on the head unit

have to be brought to their neutral or center position! The „Loudness”

function should also be deactivated.

Depending on the actual cone surface area, voice-coil diameter and

the rated power handling of the ‚satellites‘ it is recommended to set the

high-pass crossover / cut-in frequency between 40 and 240 Hz.

If the satellite highpass frequency is set too low, the mid-bass repro-

duction will be increased, but at the same time the power handling

capacity of the satellites will decrease. If the highpass frequency is set

too high, the mid-bass reproduction will become ‚thinner‘ while the

power-handling capacity of the satellites will increase.

As a general guideline, below you find a practice-proven list for appro-

priate satellite HPF crossover / cut-in frequencies covering the most

widely used dashboard, door and rear-shelf speaker diameters:

Front Satellite Speakers HIGHPASS FREQ.

10 cm Ø Coaxials or 2-Way Compos 90-120 Hz

13 cm Ø Coaxials or 2-Way Compos 80-100 Hz

16 cm Ø Coaxials or 2/3-Way Compos 70 - 80 Hz

Rear Satellite Speakers HIGHPASS FREQ.

10 cm Ø Coaxials or 2-Way Compos 100-150 Hz

13 cm Ø Coaxials or 2-Way Compos 120-130 Hz

16 cm Ø Coaxials or 2/3-Way Compos 100-130 Hz

C609 Manual DE.indd 26C609 Manual DE.indd 26 15.02.2005 10:34:06 Uhr15.02.2005 10:34:06 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Axton c 609 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info