Bedienungsanleitung Baby Lock Aria Blar (Seite 188 von 200) (Englisch)

525658

188

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

TROUBLESHOOTING

A-16

High-pitched sound

while sewing

Dust or lint is caught in the feed dogs. Remove the dust or lint. A-3

Pieces of thread are caught in the race. Clean the race. A-3

Upper threading is incorrect. Check the steps for threading the machine

and rethread the machine.

B-38

There are scratches on the bobbin case. Replace the bobbin case, or consult your

authorized retailer.

A-3

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

B-35

Character pattern

does not turn out

Wrong presser foot was used. Attach the correct presser foot.

S-68

Pattern adjustment settings were set

incorrectly.

Revise the pattern adjustment settings. S-82

Did not use a stabilizer material on thin fabrics

or stretch fabrics.

Attach a stabilizer material. S-81

Thread tension is set incorrectly. Adjust the thread tension. S-12

Fabric was pulled, pushed or fed at an angle

while it was being sewn.

Sew while guiding the fabric with your hands

so that the fabric is fed in a straight line.

S-3

Machine does not

operate

There is no pattern selected. Select a pattern. S-21, S-77

“Start/Stop” button was not pushed. Press the “Start/Stop” button. B-10

Main power switch is not turned on. Turn the main power to ON. B-15

Presser foot is not lowered. Lower the presser foot. B-10

“Start/Stop” button was pushed with the foot

controller attached.

Remove the foot controller, or use the foot

controller to operate the machine.

S-4

The “Start/Stop” button was pressed while the

machine is set for the sewing speed controller

to control the zigzag stitch width.

Use the foot controller instead of the

“Start/Stop” button to operate the machine,

or set the “Width Control” to “OFF” in the

settings screen.

B-21, S-4

All keys and buttons have been locked by

Press to unlock all keys and

buttons.

B-45, B-47

Nothing happens,

even if the LCD

display is pressed

The screen has been locked. Press either of the following keys to unlock

the screen.

—

The fabric feeds in the

opposite direction.

The feed mechanism is damaged. Contact your nearest authorized retailer. —

The LCD screen is

fogged up.

Condensation has formed on the LCD screen. After a while, the cloudiness will disappear. —

CAUTION

• This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the

upper threading is done, the machine will not operate properly. Also, depending on the pattern selected,

the machine may feed the fabric even if the needle is raised. This is due to the needle bar release

mechanism. At these times, the machine will make a sound different from what is made during normal

sewing. This is not the sign of a malfunction.

• If the power is disconnected during sewing:

Turn the main power to OFF and unplug the machine.

If you restart the machine, follow the instructions for operating the machine correctly.

Problem Cause Solution Page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baby Lock Aria Blar Seite 188

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Baby Lock Aria Blar

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info