Bedienungsanleitung Baby Lock Destiny - BLDY (Seite 19 von 196) (Englisch)

661183

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS

Embroidery Unit

a Carriage

The carriage moves the embroidery frame automatically when

embroidering. (page 197)

b Release lever (located under the embroidery unit)

Press the release lever to remove the embroidery unit. (page

198)

c Embroidery frame holder

Insert the embroidery frame into the embroidery frame holder

to hold the frame in place. (page 247)

d Frame-securing lever

Press the frame-securing lever down to secure the embroidery

frame. (page 247)

e Embroidery unit connection

Insert the embroidery unit connection into the connection port

when attaching the embroidery unit. (page 197)

Operation Buttons

a “Start/Stop” button

Press this button and the machine will sew a few stitches at a

slow speed and then begin sewing at the speed set by the

sewing speed controller. Press the button again to stop the

machine. Hold the button in to sew at the machine’s slowest

speed. The button changes color according to the machine’s

operation mode.

b “Reverse Stitch” button

For straight, zigzag, and elastic zigzag stitch patterns that take

reverse stitches, the machine will sew reverse stitches at low

speed only while holding down the “Reverse Stitch” button.

The stitches are sewn in the opposite direction.

For other stitches, use this button to sew reinforcement

stitches at the beginning and end of sewing. Press and hold

this button, and the machine sews 3 stitches in the same spot

and stops automatically. (page 83)

c “Reinforcement Stitch” button

Use this button to sew a single stitch repeatedly and tie-off.

For character/decorative stitches, press this button to end with

a full stitch instead of at a mid-point. The LED light beside this

button lights up while the machine is sewing a full motif, and

automatically turns off when the sewing is stopped. (page 83)

d “Needle Position” button

Use this button when changing sewing direction or for detailed

sewing in small areas. Press this button to raise or lower the

needle position. With this button, you can lower and raise the

needle to sew a single stitch.

e “Thread Cutter” button

Press this button after sewing to automatically trim the excess

thread.

f “Presser Foot Lifter” button

Press this button to lower the presser foot and apply pressure

to the fabric. Press this button again to raise the presser foot.

g Sewing Speed controller

Use this controller to adjust the sewing speed. Move the slide

to the left to sew at slower speeds. Move the slide to the right

to sew at higher speeds. Beginners should sew at a slow

speed.

h “Automatic Threading” button

Use this button to automatically thread the needle.

CAUTION

• Before inserting or removing the embroidery

unit, turn the main power to off.

• After the embroidery frame is set in the frame

holder, be sure the frame-securing lever is

correctly lowered.

Green: The machine is ready to sew or is sewing.

Red: The machine cannot sew.

CAUTION

• Do not press the thread cutter button after the

threads have been cut. The needle may break

and threads may become tangled, or damage

to the machine may occur.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baby Lock Destiny - BLDY Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Baby Lock Destiny - BLDY

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info