661183
204
Zoom out
Zoom in
Vorherige Seite
1/225
Nächste Seite
ERROR MESSAGES
397
Appendix
9
This message is displayed
when the machine failed to
recognize the embroidery
positioning mark.
- Confirm that the
embroidery positioning
mark is in the selected
area. If problem persists,
see page 254 to
reposition mark.
- Machine failed to
recognize printed
positioning mark. Set
“Page Scaling” to “None
(100%)”, and try printing
the embroidery
positioning mark again.
(see page 285)
This message is displayed
when the machine has
recognized the embroidery
position mark. Remove the
embroidery positioning
sticker and press
to continue. To remove the
embroidery positioning
sticker more easily, press
. (see page 254)
This message appears
when the built-in camera is
being used to align the
embroidery position, but
the embroidery positioning
sticker is too near an edge
or the pattern extends from
the embroidery frame.
Change the positioning of
the embroidery position
sticker, and then try
aligning the position again.
See page 249.
This message is displayed
when the upper thread is
broken or not threaded
correctly, and the “Start/
Stop” button or the
“Reverse/ Reinforcement
Stitch” button is pressed.
This message is displayed
when the “Presser Foot
Lifter” button is pushed
while the presser foot lever
is raised/the needle is
lowered.
This message is displayed
when the “Start/Stop
button is pushed to sew
Utility stitches or
Character/Decorative
stitches while the foot
controller is connected.
(This message does not
appear when
embroidering).
This message is displayed
when the “Start/ Stop”
button is pushed while the
machine is in embroidery
edit mode and a pattern is
being edited.
This message is displayed
when there is no stitch or
embroidery pattern
selected and the “Start/
Stop” button or the
“Reverse/Reinforcement
Stitch” button is pressed.
This message is displayed
when the bobbin thread is
running out.
This message is displayed
when the memory is full
and the stitch or pattern
cannot be saved.
This message is displayed
when, after selecting a
pattern, ,
, or is
pressed and the pattern is
about to be deleted.
This message is displayed
when the bobbin is being
wound, and the motor
locks because the thread is
tangled, etc.
This message is displayed
when there is a possibility
that the data for the
selected pattern is
corrupted.
204

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Baby Lock Destiny - BLDY wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Baby Lock Destiny - BLDY

Baby Lock Destiny - BLDY Kurzanleitung - Englisch - 67 seiten

Baby Lock Destiny - BLDY Kurzanleitung - Englisch - 66 seiten

Baby Lock Destiny - BLDY Bedienungsanleitung - Englisch - 196 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info