Bedienungsanleitung Baby Lock Ellageo Plus BLL2 (Seite 131 von 214) (Englisch)

525699

131

Zoom out

Zoom in

Vorherige Seite

1/214

Nächste Seite

PREPARING THE FABRIC

Embroidery

129

PREPARING THE FABRIC

Attaching Stabilizer to Fabric

For best results, always use stabilizer material for

embroidery. In order to prevent shrinkage of the

stitching or misaligned patterns, observe the following.

When embroidering fabrics that cannot be ironed (such

as towels or fabrics with loops that expand when

ironed) or when embroidering an area that is difficult to

iron, place the stabilizer material under the fabric

without attaching it, and then hoop the fabric and the

stabilizer in the embroidery frame.

Prepare the stabilizer material for

embroidering.

* Use a piece of stabilizer material that is larger than

the embroidery frame. When hooping the fabric in

the embroidery frame, be sure that the stabilizer

material is clamped in place on all edges in order to

prevent wrinkles in the fabric.

a Stabilizer

b Size of the embroidery frame

c Fabric

Using a steam iron, iron the stabilizer

material to the wrong side of the fabric.

a Fusible side of stabilizer

b Fabric (wrong side)

CAUTION

• Use fabrics with a thickness of less than 3 mm (approx. 1/8 inch). Using fabrics thicker than 3 mm (approx. 1/8 inch)

may cause the needle to break.

• When using layers with thicker batting etc., you can sew more attractive embroidery by adjusting the embroidery

presser foot height in the embroidery settings screen (see below).

• In the case of thick terry cloth towels we recommend that you place a piece of water soluble stabilizer on the top surface of the

towel. This will help to reduce the nap of the toweling and result in more attractive embroidery.

Memo

With this machine, the height of embroidery foot “U” is automatically set according to the thickness of the fabric being

embroidered. When embroidering thicker fabric, for example, fabric filled with batting, adjust the height of the presser foot in

the settings screen.

Press , and then press or in the PRESSER FOOT HEIGHT display on P. 3 of the screen to adjust the

height of the presser foot according to the thickness of the fabric.

To raise the presser foot, increase the setting (see page 20). (Normally, the height is set to 1.5 mm.)

CAUTION

•

Always use a stabilizer material for embroidery when

sewing stretch fabrics, lightweight fabrics, fabrics with a

coarse weave, or fabrics which cause pattern shrinkage.

Otherwise, the needle may break and cause injury. Not

using a stabilizer material may result in a poor finish to

your project.

Memo

When embroidering lightweight fabrics, such as

organdy or lawn, or when embroidering napped

fabrics, such as towel or corduroy, use water-soluble

stabilizer (sold separately) for best results. The water-

soluble stabilizer material will dissolve completely in

water, giving the embroidery a more attractive finish.

a b c a b c

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baby Lock Ellageo Plus BLL2 Seite 131

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Baby Lock Ellageo Plus BLL2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info