661200
125
Zoom out
Zoom in
Vorherige Seite
1/140
Nächste Seite
Troubleshooting
Appendix A-9
MAINTENANCE AND TROUBLESHOOTING
A
Turn the handwheel to check that the feed dogs move
smoothly and do not contact the edges of the slots in the
needle plate.
1 Correct position of feed dogs
2 Incorrect position of feed dogs
p
Insert the bobbin case so that the S mark on the
bobbin case aligns with the
z mark on the machine.
Align the S and
z marks.
1 S mark
2
z mark
3 Bobbin case
Make sure that the indicated points are aligned
before installing the bobbin case.
q
Attach the needle plate cover according to step j in
“Cleaning the race” on page A-2.
r
Check the condition of the needle, and then install it.
If the needle is in a poor condition, for example, if it is
bent, be sure to install a new needle.
Refer to “Checking the needle” and “Replacing the
needle” in the “Basic operations” section.
Checking machine operations
If the needle plate has been removed, check machine
operations to confirm that installation has been completed
correctly.
a
Turn on the machine.
b
Select stitch .
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides to check
that the needle falls at the center of the opening in the
needle plate.
If the needle contacts the needle plate, remove the
needle plate, and then install it again, starting with step
m in “Removing the fabric from the machine” on
page A-7.
1 Opening in the needle plate
2 Handwheel
Note
Be careful not to drop the removed screws in the
machine.
CAUTION
Never use a bobbin case that is scratched,
otherwise the upper thread may become
tangled, the needle may break or sewing
performance may suffer.
Make sure that you fit the bobbin case
properly, otherwise the needle may break.
a
b
b
a
CAUTION
Never use bent needles. Bent needles can
easily break, possibly resulting in injuries.
Note
After completing this procedure, continue with
the following procedure in “Checking machine
operations” to check that the machine is
operating correctly.
Memo
Since the needle may have been damaged when
the fabric was caught in the machine, we
recommend replacing it with a new one.
Note
Do not yet install the presser foot and thread.
125

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Baby Lock Katherine - BL210A wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Baby Lock Katherine - BL210A

Baby Lock Katherine - BL210A Kurzanleitung - Englisch - 4 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info