Bedienungsanleitung Baby Lock Unity - BLTY (Seite 16 von 332) (Englisch)

661225

Zoom out

Zoom in

Vorherige Seite

1/332

Nächste Seite

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS

B-14

Embroidery Unit

a Carriage

The carriage moves the embroidery frame automatically when

embroidering. (page B-65)

b Release button (located under the embroidery unit)

Press the release button to remove the embroidery unit.

(page B-65)

c Embroidery frame holder

Insert the embroidery frame into the embroidery frame holder

to hold the frame in place. (page E-17)

d Frame-securing lever

Press the frame-securing lever down to secure the embroidery

frame. (page E-17)

e Embroidery unit connection

Insert the embroidery unit connection into the connection port

when attaching the embroidery unit. (page B-65)

Operation Buttons

a “Start/Stop” button

Press this button and the machine will sew a few stitches at a

slow speed and then begin sewing at the speed set by the

sewing speed controller. Press the button again to stop the

machine. Hold the button in to sew at the machine’s slowest

speed. The button changes color according to the machine’s

operation mode.

b “Reverse Stitch” button

For straight, zigzag, and elastic zigzag stitch patterns that take

reverse stitches, the machine will sew reverse stitches at low

speed only while holding down the “Reverse Stitch” button.

The stitches are sewn in the opposite direction. For other

stitches, use this button to sew reinforcement stitches at the

beginning and end of sewing. Press and hold this button, and

the machine sews 3 stitches in the same spot and stops

automatically. (see page S-5)

c “Reinforcement Stitch” button

Use this button to sew a single stitch repeatedly and tie-off. For

character/decorative stitches, press this button to end with a

full pattern instead of mid-point. The LED light beside this

button lights up while the machine is stitching the last full motif,

and automatically turns off when the sewing is stopped. (see

page S-5)

d “Needle Position” button

Use this button when changing sewing direction or for detailed

sewing in small areas. Press this button to raise or lower the

needle position. With this button, you can lower and raise the

needle to sew a single stitch.

e “Thread Cutter” button

Press this button after sewing to automatically trim the excess

thread.

f “Presser Foot Lifter” button

Press this button to lower the presser foot and apply pressure

to the fabric. Press this button again to raise the presser foot.

g Sewing Speed controller

Use this controller to adjust the sewing speed. Move the slide

to the left to sew at slower speeds. Move the slide to the right

to sew at higher speeds. Beginners should sew at a slow

speed.

h “Automatic Threading” button

Use this button to automatically thread the needle.

CAUTION

• Before inserting or removing the embroidery

unit, turn the main power to OFF.

• After the embroidery frame is set in the frame

holder, be sure the frame-securing lever is

correctly lowered.

Green: The machine is ready to sew or is sewing.

Red: The machine cannot sew.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baby Lock Unity - BLTY Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Baby Lock Unity - BLTY

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info