• To fix the two parts, insert a 35 mm screw (h). Use a screwdriver. Figure 2
• Insert the left hand part of the rear leg (b) in the left hand swing leg (d). Make sure that the push button of the rear leg (b) s clipped into the
opening of the left hand swing leg (d). To do this correctly, the user must hear a clicking noise and see a brown push button appear on the side
of the swing bar.
• To fix the two parts, insert a 35 mm screw (h). Use a screwdriver.
•
Insert the front right hand leg (a) into the right hand swing leg (c) and the front hand left leg (a) in the left hand swing leg (d). Figure 3
• Press the push button and simultaneously drive home the front leg (a) nto the swing legs (c) and (d) until you hear a clicking noise.
A
2. Assembling the seat of the rocker swing
• Fix right hand part of the front bar (e) on the right hand swing leg (c) and the left hand part of the front bar (e) on the left hand swing leg (d).
Figures 4 and 5
• To fix the two parts, insert two 30 mm screws (g). Figure 6
• Fixer la right hand part of the rear bar (f) on the right hand swing leg (c) and the left hand part of the rear bar (f) on the left hand swing leg (d).
Figure 7
• To fix the two parts, insert two 30 mm screws (g). Figure 8
A3. Fitting the protective cover (i)
WARNING: do not use the rocker swing without its protective cover.
• Tilt the bars (e) and (f) upwards until they come together. Cover the bars (e) and (f) with the protective cover (i). Make sure the Babymoov logo
i
s facing upwards to ensure that the cover (i) is put on correctly. Figure 9
• Separate the two bars (e) and (f) sliding the protective cover (i) lalong the two bars. To ensure the cover is held firmly, fasten the Velcro in the
bottom edge of the protective cover (i). Figure 10
• When the tubes have been covered, fasten the protective nets using the press studs (j). Figure 11
A4. Fitting the 5-point safety harness
WARNING: only use the 5-point safety harness.
• To access the buckles of the harness, tilt the seat inwards. Figure 12
• Fit each strap into the buckle of the harness. Figure 13
• Thread the strap through the top slit then the bottom slit. Figures 14 and 15
• Pull on the straps so that they are quite tight. Figure 16
A5. Installing the toy bar (k)
WARNING: never lift the rocker swing using the toy bar.
• Insert the toy bar (k) into the slots either side of the seat and listen out for a clicking noise. Make sure that the toys are facing the child. Figure 17
A6. Installing the head cushion (l)
WARNING: never add any pillow, blanket or padding: use just the head cushion supplied with the rocker swing.
The head cushion (l) is an optional component offering additional support to the baby’s head for optimum comfort.
This component can be removed from the rocker swing.
• To attach or remove this head cushion (l) imply use the Velcro fastening on the rear of the protective cover (i). Figure 18
A7. Installing the batteries
The electronic box (m) f the rocker swing must be supplied by 4 x 1.5 D (LR20) batteries (not included). For optimum performance, use alkaline
batteries.
• Use a crosshead screwdriver (not included) to open the electronic box (m) on the right hand swing leg (c). Figure 19
• Insert the 4 x LR20 1.5 V batteries (not included) in the direction of the markings. Figure 20
• Screw back up the electronic box (m) with a screwdriver. Do not over-tighten.
A8. Connected to mains (adaptor supplied) (v)
IMPORTANT: make sure the rocker swing is switched off before attempting any operations.
The rocker swing can run on the mains via the adaptor supplied.
Input: 230 V / 50 Hz.
Output: 6 V / 500 mA.
• Connect the end piece of the adaptor to the socket provided for this purpose and the other part to the mains socket. Figure 21
BUBBLE ROCKER SWING • Instruction Manual
10
B. INSTRUCTIONS FOR USE OF ROCKER SWING
WARNING:
- Do not use the rocker swing if any part is broken or missing.
- Before using, check that all parts are properly locked into position and adjusted correctly.
- Never lift or carry the rocker swing with baby in it.
