Bedienungsanleitung Babymoov Expert Care (Seite 10 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

496221

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

BABY MONITOR EXPERT CARE • Instruction Manual

CONTROLS LAYOUT

Receiver

9. Visual level meter / Out-of-range indicator

10. Volume down

11. Vibration indicator

12. Speaker

13. Volume up

14. Power On/Off and vibration switch

15. Charging contacts

Transmitter

1. Nightlight

2. Microphone sensitivity adjustment

3. Transmit indicator

4. Microphone

5. Nightlight VOX control button

6. Power On-Off and Nightlight switch

7. Power on / Battery low indicator

8. DC Jack

Charger

16. Charging pins

17. DC Jack

18. Charging Indicator

Transmitter and receiver

19. Channel switch

20. Digital codes switches

NB.: If you notice any interference when in operation, change channel or alter the numeric code combination.

Make sure that you always keep the same settings for the transmitter and receiver.

eceiver

Press the latch cover and slide it to gain access to

the battery compartment. Remove the battery.

roceed as for the transmitter to set the channel and

numeric code.

ake sure that the settings for the transmitter and

receiver are exactly the same.

OPERATION

A / Transmitter

• Set the power ON/OFF switch (6) to ON position to turn on the unit. The power on indicator (7) will light

up steady green.

• Place the transmitter about 1 m from the cradle, directing the microphone (4) towards the baby.

• Adjust the sensitivity of the microphone by using button (2): press upwards to increase sensitivity and

downwards to reduce it (there are 5 levels).

• As soon as the transmitter detects a sound, the transmit indicator lights up red.

• The night light (1) can be set permanently ON by moving the power ON/OFF switch (6) to position .

The night light can also be set to be VOX (voice activated) by momentarily pressing the button 5. Under

VOX mode, the night light will be switched on once the microphone detects a sound and automatically

goes off a few seconds after the microphone stops picking up any sound.

• The condition of the batteries is shown by the battery low indicator “Power” (7). When the battery power

is being consumed, the indicator starts flashing.

B / Reveiver

• Set the power ON/OFF switch (14) to ON position to turn on the unit. The power on indicator (7) will light

up steady green.

• Place the receiver at a reasonable distance away from the transmitter to avoid feedback. Too close a distance

will create a screeching sound.

• Once the unit receives a signal from the transmitter, the LED of the visual level meter (9) light up. The louder

the baby’s voice, the more number of LED will be lighted up.

• The loudspeaker volume can be adjusted by using buttons (10) and (13). Each time you press on one of

these buttons, you will hear a “beep” whose volume corresponds to the level you have just selected. If

you press button 10 to its lowest level, you will no longer hear a beep which means that your receiver is

in mute mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Babymoov Expert Care Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info