Bedienungsanleitung Babymoov Expert II (Seite 9 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

496289

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

N.B.: Please set the range check function to OFF for normal baby monitor operation or otherwise the

communication range between transmitter and receiver will become very short.

2. The sensor inside the unit will detect the baby’s room temperature and its current reading is shown on

the LCD screen of both transmitter as well as receiver. The normal operating range of the temperature

sensor is -9°C to +50°C . Temperature outside this range will also be shown in the LCD screen except

with less accuracy. In case there is a sudden tempaerature change (eg. you bring the transmismitter

from indoor to outdoor during winter time), the sensor may need to take a few minutes before it can

settle to the new envoiroment and show the correct reading on the LCD screen.

3. When the power ON/OFF switch (1) is set at ON position, a momentarily press of the mode button (3)

will cause the LCD screen to show the different settings in a cyclic order. A screen showing operating

channel/digital code, output power setting, out-ofrange alert setting or range setting will automatically

return to screen showing baby’s room temperature after 5 seconds if no further button is pressed.

BABYPHONE EXPERT II • Instruction Manual

8. The night light (4) can be set permanently ON by moving the power ON/OFF switch (1) to position,

the night light icon will be shown in the LCD. The night light can also be set to be VOX (voice

activated) by momentarily pressing the mode button (3) , the VOX icon will be shown besides the

icon. Under VOX mode, the night light will be switched on once the microphone (5) detects a sound

and automatically goes off a few seconds after the microphone (5) stops picking up any sound.

Momentarily press of the mode button (3) will cause the night light to toggle between permanent ON

and VOX.

9. The condition of the battery is shown by the battery status indicator . When the battery power is

being consumed, the segments within the battery status indicator gradually falls. Once the indicator

becomes empty, it will start flashing, besides, the transmitter will also send out a signal to the receiver

to alert the parents.

10. Each time a button is pressed, a beep tone will be heard to validate your entry being recognized by

the unit.

4. Place the transmitter about 1 m from the crib with the microphone (5) facing towardsthe baby.

5. Adjust the microphone sensitivity using the up/down button (2) such that the unit will be set to transmit

whenever the microphone (5) picks up a sound at your desirable loudness level. The microphone

sensitivity bar graph in the LCD will also change correspondingly. More segment of bar graph shown

means the unit is more sensitive to sound.

6. Once the unit is in transmit mode, the LCD will be backlighted and the transmit icon will be shown.

The transmitter will return to standby mode a few seconds after the microphone (5) stops picking up

any sound and the transmit icon goes off. The LCD backlight will also go off to save battery power.

7. When the Out-of-range alert function is set to On, the transmitter will transmit a signal to the receiver

at regular intervals even when the microphone (5) does not pick up any sound. The transmit icon

will blink correspondingly in the LCD.

RECEIVER

1. Setting of channel, digital code, upper/lower temperature limit and Out-of-range

alert function.

1. a. Set the power ON/OFF switch (8) to ON position to turn on the unit. The LCD screen

will show up and become backlighted. Press and hold mode button (10) for at least

5 seconds to enter into programming mode. A confirmation beep tone will be

heard once the unit goes into programming mode successfully and the LCD wil

show following:

▼ Flashing

▼ Light up steadily

1. b. Use Up/Down button (9) to select a channel same as the transmitter. Each press

of the button will cause the channel no. to advance or retreat one step. Press and

hold the Up or Down button (9) will cause the channel no. to scroll up or down

rapidly. Confirm your selection by pressing the mode button (10). The LCD will show

following:

1. c. Now select the same digital code as the transmitter using the Up/Down button (9).

Each press of the button will cause the digital code to advance or retreat one step.

Press and hold the Up or Down button (9) will cause the digital code to scroll up or

down rapidly. Confirm your selection by pressing the mode button (10). The LCD will

show following :

1. d. Now select the same setting for Out-of-range alert function as per the transmitter

using Up/Down button (9). If a different setting is selected, either false alarm will

be heard or no alarm will be provided even when receiver falls beyond the

communication range of transmitter. Confirm your selection by pressing the mode

button (10). The LCD will show following:

N.B. In case the transmitter is set to operate with range check function, the reciever will

automatically enters range check mode no matter the out-of-range setting is ON or OFF.

Out-of-range alert function

is enabled

CH2 and digital code 28

is selected

High output power is selected

Current baby's room temperature is 23°C

BBPhone Expert II-Notice 5/12/06 11:41 Page 17

Babymoov Expert II Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info